User manual CUISINART CSB-55N

[. . . ] ® INSTRUCTION BOOKLET SMARTSTICKTM EXTENDIBLE SHAFT HAND BLENDER CSB-55 TABLE OF CONTENTS: Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 2 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 4 Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. [. . . ] Remove the wall bracket, leaving the template in place. Mark the wall with a pencil in the locations for screw holes indicated by the template. With a drill, make a 3/16" starter hole for each screw. Push completely into the hole with fingers, or tap in gently with a hammer. Screw a mounting screw into each hole leaving 1/8" to 1/4" of the head and screw exposed. Position the two mounting holes of the wall bracket over the screw heads and slide wall bracket down the wall until the bracket is resting against the screw head, and will not slide any further. If the wall bracket feels too loose against the wall, remove bracket, put screws further into wall and replace bracket. SmartStickTM MINI PREP® Chopper Grinder Attachment H I E G B A C F D ® SmartStick EXTENDABLE SHAFT TM PRESS BUTTON TO DETACH ® SmartStickTM MINI PREP® Chopper Grinder Attachment ® SmartStickTM MINI PREP® Chopper Grinder Attachment Reversible Blade. ® SmartStick EXTENDABLE SHAFT TM PRESS BUTTON TO DETACH ® Use only this piece for wall mounting. Connect to other half for countertop storage. Place the assembled SmartStickTM Hand Blender into the wall bracket. The unit will hang from the bracket, held in place by the motor body width. To reduce the risk of fire or electric shock, do not operate any heating appliance beneath the mounting unit. Do not mount the storage bracket/ unit over or near any portion of a heating or cooking appliance or a sink or basin. The Cuisinart SmartStickTM Mini Prep® Chopper Grinder attachment is equipped with a reversible blade. This blade is sharp on one side and blunt on the other. The blade is attached to a plastic ring which slides over the blade assembly shaft, so it can be easily turned over to select the appropriate blade. A guide for proper blade selection follows in the section, Chopper Grinder Tips for Processing Foods. Before you process any food, assemble the parts. Place the Prep Bowl on a flat, dry, stable surface. It should be close to an electrical outlet of the same voltage as stated on the rating plate on the SmartStickTM Hand Blender. 12 13 2. The metal blade assembly shaft is attached to the bottom of the Prep Bowl. If not already in place, slide the fully assembled Blade Assembly over the top of the blade assembly shaft. Putting together the Blade Assembly: Connect the Blade Ring (F) to the Plastic Blade Sheath (G). Line up the blade ring opening with the plastic sheath. Let the blade ring slide to the bottom of the plastic sheath. [. . . ] We warrant that your Cuisinart® SmartStickTM Extendable Shaft Hand Blender will be free of defects in materials and workmanship under normal home use for three years from the original date of purchase. We suggest you complete and return the enclosed warranty registration card promptly. However, return of the card is not a condition of this warranty and does not eliminate the need for the consumer to maintain the original receipt of purchase. If your unit should prove to be defective within the warranty period, we will repair or replace it at our option without charge to you. [. . . ]