User manual CULLIGAN SOFT-MINDER TWIN MODELS FROM 2005

[. . . ] B 04/06/05 DCO # 7499 Owners Guide & Installation Instruction Supplement Soft-Minder Twin ® Models From 2005 © 2005 Culligan International Company Printed USA Thank You And welcome to your new world of better living with Culligan water. The Culligan Soft-Minder TwinTM Water Softeners are tested and certified by WQA according to WQA S100 for calcium and magnesium reduction (hardness). For installations in Massachusetts, the Commonwealth of Massachusetts Plumbing Code 248 CMR shall be adhered to. Consult your licensed plumber for installation of the system. This system and its installation must comply with state and local regulations. [. . . ] Allow the unit to complete the recharge cycle automatically. If tastes and odors return frequently, even after sanitization, a continuous chlorination system may be needed. Send a water sample to a qualified laboratory for bacterial analysis. Analyzing the System Analyzing the problem involves three basic steps: 1. Check the system in all cycle positions. Compare the data to normal operating data. Determine which component may cause the problem (troubleshooting). If steps 1-3 did not reveal the problem, initiate a regeneration cycle and manually cycle the valve to brine draw (#2 position). Allow the unit to complete the brine draw cycle and observe how the system reacts. Although it may be possible to solve a specific problem simply by changing a component, analyzing the entire system can reveal additional problems which would otherwise require extra service calls. "Parts changing" is not the same as service. Check the System The following tools are needed to collect data: 1. Hardness, iron and chlorine test kits 2. Calculator The customer can provide most data. By collecting data prior to a service call, a "first guess" about the cause of the problem can be made and the need for any special parts can be determined. If the problem is as simple as lack of salt in the brine tank, a service call may not be needed at all. At the end of Appendix A is a recommended system data sheet that will assist the troubleshoot process. 16 Culligan Soft-Minder® Twin Installation Before Leaving the Installation Site Sanitizing the softener. See sanitizing procedure on previous page. Ensure that the brine tank has water to the level of the float. Add water to the tank with a hose or put the unit into a full recharge so that the brine refill cycle will fill the tank with the proper amount of water. The water heater will hold hard water for several days. Advise the customer that the existing water volume in the tank will need to be used before the hot water is soft. [. . . ] 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 16 17 18 19 20 21 22 23 Parts List 31 Parts List Power Head 32 Culligan Soft-Minder® Twin Parts List Control Valve Parts List Item No. 8 10 11 12 17 18 19 21 23 25 26 27 28 30 29 34 36 39 * * * * Part No. 01013002 01017766 01013003 01013004 01009210 00401865 00402016 01013005 01009225 01017805 00402011 00401871 00445244 00401872 00402012 01013006 01009298 01009212 01013007 01013009 01013010 01017806 01017807 00401865 01003002 Description Nut Transformer w/ Power Cord Drive Gear Assembly, Lower Drive Gear Assembly Geneva Wheel Cover Screw Retaining Ring Ground Plate Screw Drive Motor, 24 Volts Screw Washer Microswitch (Homing) Nut Screw Drive Gear Assembly, Upper Strain Relief Retaining Ring Triple Cam Washer Spacer Microswitch (Program) Decal Cover Cover Screen Cover Screen Retainer Qty. 2 1 1 1 1 1 2 1 1 1 2 2 1 1 1 2 1 1 1 2 2 1 1 1 1 1 * Not Shown Parts List 33 Parts List 9100 Second Tank Assembly Item No. [. . . ]