User manual CURTIS TID889

[. . . ] in a high humidity area such as a bathroom near a heater in an area exposed to direct sunlight (e. g. , inside a parked car, where it can become extremely hot) near sources of strong magnetism, such as televisions, speakers, or magnets where there is a lot of movement or vibration, such as on a car dashboard or an unstable shelf USING ON DRY CELL BATTERIES A Open the battery compartment and insert two LR6 (size AA) alkaline batteries with the and marks correctly aligned. Battery replacement The battery indicator in the display according to the remaining power of the batteries. Replace the batteries when lights. If the unit remains in use after lights. If the cover of the battery compartment comes off B Note on dry cell batteries Do not mix the different types of batteries, or an old battery with a new one To prevent the risk of electrolyte leakage or explosions, never recharge the batteries, apply heat to them, or take them apart, must set recharge button to "OFF". [. . . ] If the cover of the battery compartment comes off B Note on dry cell batteries Do not mix the different types of batteries, or an old battery with a new one To prevent the risk of electrolyte leakage or explosions, never recharge the batteries, apply heat to them, or take them apart, must set recharge button to "OFF". When not using the batteries, remove them to pre vent needless battery wear If liquid leaks from the batteries, wipe thoroughly to remove USING ON RECHARGEABLE BATTERIES C Be sure to use size AA Ni-Cd 1. 2V rechargeable batteries. which are commercially available . Be sure to read the instructions of the purchased rechargeable batteries before use Before charging the batteries, close the disc compartment, you cannot charge the batteries while it is opened Only for the special rechargeable batteries which expose part on the polarity. Insert the rechargeable batteries with the and marks correctly aligned. When recharge please switch the recharge button to "on", after recharging or in other condition switch to "off ", otherwise the CD player will be damaged 3. 1 to DC 4. 5 V jack 2 to a wall outlet 4. After charging, disconnect the AC adaptor. Time to recharge the batteries Recharge the batteries when lights, If the unit remains in use after lights, the current operation will stop. ATTENTION The rechargeable batteries are recyclable, At the end of their useful life, it may be illegal to dispose the batteries into the municipal waste stream under various state and local laws. Check with your local solid waste officials in your area for details about recycling options or proper disposal. A Ni-Cd Cd 2 B C ON OFF CHARGE 1 DC 4. 5V BEFORE PLAYBACK HOLD switch D Release the HOLD switch to OFF position before playback. When desired track is display, press PROGRAM key to register, Then track No. Repeat 2-3 (up to 20 tracks) after register 20 tracks. display shows the first registered track. Registered tracks can be check by press PROGRAM key, And it can be changed by repeat 2-3. Press play key, then PROG stops flashing and starts playing. Open the door or power off to clean programing 3 CONNECTION TO AN EXTERNAL UNIT I Use a commercially available connection cord which has a 3. 5mm stereo plug at one end and two phono plugs at the other end. Connect the stereo plug to the LINE OUT jack of the unit and connect the phono plugs to the analog input (AUX) terminals of the external unit. NOTE Turn off the power of both units before connection. DO NOT connect to the PHONO(magnetic pickup) inputs of an amplifier. Volume and bass boost on this unit have no effect on the line output. MAINTENANCE To clean the lens J If the lens become dirty, the player will skip or not play, If this occurs, clean the lens in the following. [. . . ] DO NOT connect to the PHONO(magnetic pickup) inputs of an amplifier. Volume and bass boost on this unit have no effect on the line output. MAINTENANCE To clean the lens J If the lens become dirty, the player will skip or not play, If this occurs, clean the lens in the following. manner, To remove dust or dust particles, first use a camera lens blower/brush 1 to blow a few times to loosen particles, then gently brush the lens 2 clean finish by blowing the lens again. Note Take care not to get too much solution on the swab. [. . . ]