User manual D-LINK DES-1228 INSTALLATION GUIDE

[. . . ] Install the DES-1228 on a sturdy, level surface that can support its weight, or in an EIA standard-size equipment rack. When installing the Switch on a level surface, attach the rubber feet to the bottom of each device. The rubber feet cushion the switch and protect the switch case from scratching. Attach the adhesive rubber pads to the bottom 2 Rack Mounting The DES-1228 can be mounted in an EIA standard-size, 19-inch rack, which can be placed in a wiring closet with other equipment. Attach the mounting brackets to both sides of the Switch (one at each side), and secure them with the provided screws. Use the screws provided. [. . . ] When the Power LED light is off, the power cord is not or improperly connected. CPU LEDs ( Management Indicator) Blinking When the CPU is working, the CPU LED is blinking. Off The CPU is idle. Ports 1 ~ 24 Status LEDs Link/Act On When the Link/Act LED light is on, the respective port is successfully connected to an Ethernet network. Blinking When the Link/Act LED is blinking, the port is transmitting or receiving data on the Ethernet network. Off 100Mbps On When the 100Mbps LED light is on, the respective port is connected to a 100Mbps Fast Ethernet network. When the respective port is connected to a 10Mbps Ethernet or no link. 5 No link. Off Option Ports 25~26 10/100/1000 Base-T / Mini-GBIC Status LEDs FX Link On When the FX Link LED light is on, the respective port is connected to a 100 or 1000Mbps Ethernet network. Off No link or linking the copper ports. Link/Act On When the respective combo port is connected to a network, the Link/Act LED light is on. Blinking When the LED is blinking, the respective combo port is transmitting or receiving data on a network. 1000Mbps On When the 1000Mbps LED light's on, the respective port is connected to a 1000Mbps Gigabit Ethernet network. Off When the respective port is connected to the 100Mbps Fast Ethernet or no link. 100Mbps On When the 100Mbps LED lights on, the respective port is connected to a 100Mbps Fast Ethernet network. When the respective port is connected to a 1000Mbps Gigabit Ethernet network or no link. Off Ports 27~28 10/100/1000 Base-T LEDs Link/Act On When the Link/Act LED light is on, the respective port is successfully connected to an Ethernet network. Blinking When the Link/Act LED is blinking, the port is transmitting or receiving data on the Ethernet network. Off No link. 6 1000Mbps On When the 1000Mbps LED light is on, the respective port is connected to a 1000Mbps Gigabit Ethernet network. Off When the respective port is connected to a 10Mbps Ethernet or 100Mbps Fast Ethernet network, or no link. 100Mbps On When the 100Mbps LED light is on, the respective port is connected to a 100Mbps Fast Ethernet network. When the respective port is connected to a 10Mbps Ethernet or 1000Mbps Gigabit Ethernet network. Off Installing the SmartConsole Utility The SmartConsole Utility allows a user to monitor and configure multiple D-Link Web-Smart Switches from a workstation connected to the network. Follow these steps to install the SmartConsole Utility: 1. Insert the Utility CD in the CD-Rom Drive. From the Start menu on the Windows desktop, choose Run. In the Run dialog box, type D:\SmartConsole Utility\setup. exe ( where D:\ represents the drive letter of your CD-ROM) your CD-Rom drive is located) and click OK. [. . . ] This will automatically load the web configuration in your web browser. When the following logon box appears, enter "admin" for the password. Press Ok to enter the main configuration window. (Figure 3. ) Figure 3 8 Once you have successfully logged in, the device status page will appear. [. . . ]