User manual D-LINK DES-3010FL COMMAND LINE INTERFACE REFERENCE MANUAL

[. . . ] DES-3010F / DES-3010G / DES-3018 / DES-3026 Managed 8/16/24-port 10/100Mbps N-Way Fast Ethernet Switch Command Line Interface Reference Manual First Edition (May 2005) 651ES3026015 Printed In Taiwan RECYCLABLE Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Using the Console CLI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Command Syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Basic Switch Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] broadcast [enabled | disabled] - Enables or disables broadcast storm control. multicast [enabled | disabled] - Enables or disables multicast storm control. dlf [enabled | disabled] - Enables or disables dlf traffic control. threshold <value 64-1024000> - The upper threshold at which the specified traffic control is switched on. The value is the amount of broadcast/multicast/dlf traffic, in Kbps, received by the Switch that will trigger the storm traffic control measures. The value ranges in size from 64 to 1024000 Kbps. Restrictions Example usage: To configure traffic control and enable broadcast storm control system wide: DES-3026:4# config traffic control all broadcast enabled Command: config traffic control all broadcast enabled Success. DES-3026:4# Only administrator-level users can issue this command. Description Parameters 73 DES-3010F / DES-3010G / DES-3018 / DES-3026 Layer 2 Switch CLI Reference Manual show traffic control Purpose Syntax Description Parameters Restrictions Example usage: To display traffic control setting for ports 1-5: DES-3026:4#show traffic control group_list 1-5 Command: show traffic control group_list 1-5 Group [port] ---------1 2 3 4 5 Threshold (Kbit/sec) -----------64 64 64 64 64 Broadcast Storm --------------Disabled Disabled Disabled Disabled Disabled Multicast Storm --------------Disabled Disabled Disabled Disabled Disabled Destination Lookup Fail ---------------Disabled Disabled Disabled Disabled Disabled Used to display current traffic control settings. show traffic control {ports <portlist>} This command displays the current storm traffic control configuration on the Switch. ports <portlist> - Enter a port or range of ports to be viewed. None. Total Entries: 5 DES-3026:4# 74 DES-3010F / DES-3010G / DES-3018 / DES-3026 Layer 2 Switch CLI Reference Manual 12 QOS COMMANDS The DES-3026 switch supports 802. 1p priority queuing. The Switch has 4 priority classes of service. These priority classes of service are numbered from 3 (Class 3) -- the highest priority class of service -- to 0 (Class 0) -- the lowest priority class of service. The eight priority queues specified in IEEE 802. 1p (p0 to p7) are mapped to the Switch's priority classes of service as follows: · · · · · · · · Priority 0 is assigned to the Switch's Q0 class. Priority 1 is assigned to the Switch's Q0 class. Priority 2 is assigned to the Switch's Q1 class. Priority 3 is assigned to the Switch's Q1 class. Priority 4 is assigned to the Switch's Q2 class. Priority 5 is assigned to the Switch's Q2 class. Priority 6 is assigned to the Switch's Q3 class. Priority 7 is assigned to the Switch's Q3 class. Priority scheduling is implemented using two types of methods, strict priority and round-robin priority. If no changes are made to the QoS priority scheduling settings the method used is strict priority. [. . . ] The user may set the hold time from 100 to 255 seconds. Restrictions Example usage: To change the time interval of the discovery protocol: DES-3026:4#config sim candidate dp_interval 30 Command:config sim candidate dp_interval 30 Success. DES-3026:4# To change the hold time of the discovery protocol: DES-3026:4#config sim candidate hold_time 120 Command: config sim candidate hold_time 120 Success. DES-3026:4# Only administrator-level users can issue this command. 139 DES-3010F / DES-3010G / DES-3018 / DES-3026 Layer 2 Switch CLI Reference Manual 25 COMMAND HISTORY LIST The command history list commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command ? [. . . ]