User manual D-LINK DHP-302 VERSION 1.1

[. . . ] 8 Using the Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Synchronization complete After a few seconds, successful synchronization should occur. This is visible when the remote adapter's AP LED switches off indicating that it is securely configured. The local adapter AP LED however, will continue to remain solidly lit and the throughput LED should turn Green. Remote Adapter Local Adapter Note: When adding more adapters, repeat steps 1 to 3. At the end of this process, only the local adapter should have the AP LED lit. Also, the adapters will keep their security settings even after the power is removed from the units. To reset / switch-off any adapter security back to default: Depress and hold (up to 15 seconds) the push button until the AP LED turns off. This will reset the unit back to the factory default settings D-Link DHP-302 User Manual 10 Section 2 - Installation Using the Setup Wizard Follow the simple steps below to run the Setup Wizard to guide you quickly through the installation process. Insert the D-Link DHP-302 CD into your CD-ROM drive. If the CD Autorun function does not automatically start on your computer, click Start > Run. In the Run command box type "D:\DHP302. exe", where D: represents the drive letter of your CD-ROM. If it does start, proceed to the next screen. Click on Install Utility The InstallShield Wizard will begin the DHP-302 software installation. Click Next D-Link DHP-302 User Manual 11 Section 2 - Installation Click Next Click Finish D-Link DHP-302 User Manual 12 Section 3 - Configuration Configuration After you have completed the D-Link Powerline Utility installation wizard, double-click the D-Link Powerline HD Utility icon on your desktop to start the configuration of the DHP-302. Double-click the D-Link Powerline HD Utility icon The utility provides you with the option of setting your own unique Network ID and the ability to prioritize traffic passing through the network. The color of text on the Device Name, Network ID, MAC, and Location columns represent the status of powerline network. · Green text - Powerline network is encrypted with a non-default Network ID. · Red text - Powerline network is encrypted with the default Network ID. · Grey text - Powerline network is not connected due to a different Network ID. D-Link DHP-302 User Manual 13 Section 3 - Configuration Red text on the Device Name, Network ID, MAC & Location columns mean that the powerline network is encrypted with the default Network ID (D-Link). Follow the steps below to encrypt the network with a non-default Network ID: · Single-click on the nodes that you want to change. · Once all the nodes you want to encrypt with a non-default Network ID are highlighted, click the Security page. · Change to different Network ID. · Press Save Settings. D-Link DHP-302 User Manual 14 Section 3 - Configuration Setup This screen shows the current configuration of the DHP-302. Device Name: Show name of devices that have been discovered. [. . . ] Port: Input the port number to have priority. Priority: Input port priority from 1 to 6. The highest priority is 6, and the lowest is 1. Note: Rule 1 has priority over Rule 2 D-Link DHP-302 User Manual 19 Section 3 - Configuration System With the power saving mode enabled and the ethernet link activity being down for 15 minutes, the DHP-302 will automatically go into stand-by mode. [. . . ]