User manual DA-LITE GROMMET FRAME

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual DA-LITE GROMMET FRAME. We hope that this DA-LITE GROMMET FRAME user guide will be useful to you.

Lastmanuals help download the user guide DA-LITE GROMMET FRAME.


Mode d'emploi DA-LITE GROMMET FRAME
Download

You may also download the following manuals related to this product:

   DA-LITE GROMMET FRAME BROCHURE (335 ko)
   DA-LITE GROMMET FRAME DATASHEET (157 ko)
   DA-LITE GROMMET FRAME BROCHURE 2 (297 ko)

Manual abstract: user guide DA-LITE GROMMET FRAME

Detailed instructions for use are in the User's Guide.

[. . . ] Slide the side frame sections onto the top frame section. Insert one 3/8" bolt at each corner and tighten (do not overtighten). The next step is much easier with two people. With one person at each end, slide the bottom frame section into the side frame sections. [. . . ] Wall mount installation: There are 6 hanger brackets for smaller frames with a one-piece top frame rail. 8 hanger brackets are provided for larger frames with two-piece top frame rails. Determine where the Series 200 frame will be mounted on the wall. Consider the following before attaching the hanger brackets to the wall. - The hanger brackets must be anchored to a supported section of the wall, such as a wall stud. - The hanger brackets should be spaced on the wall so they line up with the S-hooks on the frame. This will prevent the lace cord from being pinched between the frame and hanger. - You will need at least 2" above the hanger bracket to mount the Series 200 frame (see Figure 2). - Frames with one-piece top frame rails should be supported at the center of the frame and about 2-4 feet from each end of the frame. - Frames with two-piece top frame rails should be supported about 2-3 feet on each side of the center joint and about 2-4 feet from each end of the frame. Attach 3 or 4 hanger brackets (as required above) at the same height along the wall. To determine the distance between the upper and lower hanger brackets you must measure the overall height of the frame. If your frame has the Pro-Trim border subtract 3-3/4" from the overall height. If your frame does not have the Pro-Trim border subtract 3-1/2" from the overall height. Using this number, measure down from each hanger bracket and mark the wall. 1 SERIES 200 INSTALLATION (CONTINUED) 2. Line up the lower hanger bracket with the mark and secure it to the wall. Remove the frame clamp from the hanger brackets and position the Series 200 frame on the hanger brackets as shown in Figure 2. Place the frame clamp onto the hanger bracket and secure it with the supplied hex nut. SERIES 200 FRAME HEX NUT FRAME CLAMP 2" MINIMUM UPPER HANGER BRACKET EQUALS OUTSIDE FRAME HEIGHT -3-3/4" WITH PRO-TRIM BORDER -3-1/2" WITHOUT PRO-TRIM BORDER (PRO-TRIM BORDER ADDS 1/4" TO FRAME HEIGHT LOWER HANGER BRACKET FIGURE 2 SERIES 300 INSTALLATION The Series 300 frame is supplied with eyebolts for ceiling installations and hanger brackets for wall mount installations. Ceiling installation: The frame is predrilled for the attachment of the eyebolts. There are 3 eyebolts for smaller frames with a one-piece top frame rail. Larger frames with two-piece top frame rails will have 4 eyebolts. Insert the eyebolts through the frame and attach the hex nut to the eyebolt. [. . . ] Using this number, measure down from each hanger bracket and mark the wall. 2 SERIES 300 INSTALLATION (CONTINUED) 2. Line up the lower hanger bracket with the mark and secure it to the wall. Remove the frame clamp from the hanger brackets and position the Series 300 frame on the hanger brackets as shown in Figure 3. Place the frame clamp onto the hanger bracket and secure it with the supplied hex nut. SERIES 300 FRAME HEX NUT FRAME CLAMP 3" MINIMUM UPPER HANGER BRACKET EQUALS OUTSIDE FRAME HEIGHT -4-3/4" WITH PRO-TRIM BORDER -4-1/2" WITHOUT PRO-TRIM BORDER (PRO-TRIM BORDER ADDS 1/4" TO FRAME HEIGHT LOWER HANGER BRACKET FIGURE 3 SPLIT FRAME ASSEMBLY 1. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE DA-LITE GROMMET FRAME

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual DA-LITE GROMMET FRAME will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag