User manual DA-LITE TENSIONED CONTOUR ELECTROL

[. . . ] The Da-Lite Difference. Instruction Book for DA-LITE SCREEN COMPANY, INC. 3100 North Detroit Street Post Office Box 137 Warsaw, Indiana 46581-0137 Phone: 574-267-8101 800-622-3737 Fax: 574-267-7804 Toll Free Fax: 877-325-4832 www. da-lite. com e-mail: info@da-lite. com TensIoned ConTour® eleCTrol® IMPORTANT SAFETY INSTRUCTIONS When using your video equipment, basic safety precautions should always be followed, including the following: 1. Read and understand all instructions before using. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. [. . . ] If the screen does not drop enough, raise the screen about one foot and adjust the limit switch again. Repeat until the desired position is set. CAUTION: Do not adjustwithmoreblackthan what was ordered. At least 1-1/2 wraps of fabric must remain on the roller. This screen comes standard 12" at the top. s RoTaTe uP FIGURE 4 3 FIGURE 5 SCREEN AdjUSTMENT FOR 120v SCREENS WITH A BUILT-IN LOW vOLTAGE CONTROL OR vPI 1. locate the wall switch and remove the cover plate from the 3-button wall switch and remove the switch from the junction box. locate the two tactile buttons on the back of the switch. They are square silver with black round buttons. see figure 8 (VPI) or figure 10 (lVC) for diagram. To adjust the down limit switch, press and hold the down tactile button until the led on back of switch turns solid red. This will put the motor in limit set mode. Turn the wall switch over and use the down button on front of switch. Press and hold until the desired travel position is reached. If you travel to far down you can press the up to move the screen upward. If you press and let go of either up or down button the motor will do a small jog in that direction for finer adjustment of screen. once desired position is reached turn switch over press and hold down tactile button until the led on back of switch blinks red twice. To adjust the up limit switch, press and hold the up tactile button until the led on back of switch turns solid green. This will put the motor in limit set mode. Turn the wall switch over and use the up button on front of switch. Press and hold until the desired travel position is reached. If you travel to far up you can press the down to move the screen downward. [. . . ] Please see wiring diagram included in wall switch box included with screen. gRound To Case WhITe blaCk (doWn) Red (uP) gRound­musT be ConneCTed To buIldIng gRound aC (Common) sPdT sWITCh WITh CenTeR off uP off doWn blaCk aC hoT 120VaC 60hZ 1 amP Red blaCk/YelloW noTe: a sIngle sWITCh CannoT be used To oPeRaTe moRe Than one sCReen. ConTaCT The faCToRY foR fuRTheR InfoRmaTIon. ThIs sWITCh Can noT be used WITh lVC. UP RJ-22 JaCk STO P uP do (Re W Co n d) (b (W mm la hIT on Ck ) e) 120V WIRING DIAGRAM WITH OPTIONAL BUILT-IN VIDEO PROJECTOR INTERFACE FIGURE 8 led uP lImIT TaCTIle buTTon RJ-22 InPuTs RJ-22 JaCk RJ-22 ouTPuT dRY ConTaCTs CAUTION: THE PROJECTOR MUST BE TURNED OFF BEFORE CONNECTING THE TRIGGER WIRES TO THE PROJECTOR. FAILURE TO DO SO MAY DAMAGE THE CONTROLLER. use 2-conductor 20-24 gauge wire to extend the low voltage connection from the projector's 5 or 12-volt screen trigger output to the length required to reach the VPI. [. . . ]