User manual DAELIM B-BONE

[. . . ] OWNER S MANUAL IMPORTANT NOTICE WELCOME Thank you for purchasing an Daelim vehicle. We hope you enjoy safe riding. OPERATOR AND PASSENGER This motorcycle is designed to carry the operator and one passenger. WARNING Attempting to change the pre-set maximum speed may cause danger and will void the Daelim warranty. ON-ROAD USE This motorcycle is designed to be used only on the road. READ THIS OWNER'S MANUAL CAREFULLY Pay special attention to statements preceded by the following words: WARNING Indicates a strong possibility of severe personal injury or death if instructions are not followed. CAUTION Indicates a possibility of personal injury or equipment damage if instructions are not followed. NOTE Gives helpful information. This manual is an important and integral part of your vehicle. keep it with your vehicle at all times, even though your vehicle is resold. CONTENTS SPECIFICATION OPERATION INSTRUCTION SAFETY PRECAUTIONS PRIOR TO STARTING VEHICLE FOR SAFE DRIVING OPERATION CORRECT ATTIRE MODIFICATION ATTACHMENT MUFFLER 3 4 4 5 5 6 7 7 8 8 9 12 12 12 12 13 13 13 14 14 15 15 EQUIPMENT USAGE STEERING STEM LOCK SEAT LOCK HOLE FOR A CHAINLOCK CORRECT DRIVING OPERATION STARTING THE ENGINE AFTER STARTING ENGINE PROPER DRIVING METHODS STOPPING 16 16 16 16 17 17 19 20 21 23 23 24 24 26 27 27 28 28 28 PARTS LOCATION METER READING AND USAGE METER WARNING AND INDICATOR LAMPS MALFUNCTION INDICATOR LAMP SELF INSPECTIONS BEFORE OPERATION INSPECTION OF CONCENED AREA BRAKE INSPECTION TIRE INSPECTION FUEL CHECK ENGINE OIL CHECK LIGHTS AND WINKER INSPECTION BULB REPLACEMENT METHOD REAR VIEW MIRROR FUEL LEAK INSPECTION SWITCH OPERATION MAIN SWITCH START BUTTON HEADLIGHT PASSING SWITCH WINKER SWITCH HORN BUTTON 1 MAINTENANCE MAINTENANCE SCHEDULE MAINTENANCE PRECAUTIONS REPLENISHING FRONT / REAR BRAKE FLUID BRAKE HOSE, PIPE LEAKAGE, DAMAGE, ASSEMBLY STATE FRONT BRAKE PAD WEAR CHANGING ENGINE OIL TRANSMISSION OIL INSPECTION TIRE PRESSURE INSPECTION BATTERY INSPECTION FUSE REPLACEMENT AIR CLEANER ELEMENT INSPECTION CABLE RUBBER PART SPARK PLUG HANDLING FOR POOR STARTING SIDE STAND INSPECTION CLEANING GENERAL CLEANING STORAGE GUIDE FRAME AND ENGINE NUMBER 29 29 31 31 32 32 33 34 35 35 36 37 38 38 39 40 40 41 41 42 DRIVING METHOD DRIVING POSITION PRECAUTION WHEN DRIVING STARTING 43 43 44 45 46 46 46 47 48 49 50 50 50 51 51 51 52 53 TURNING METHOD PRINCIPLE OF TURN EFFECT OF SPEED 3 POSITIONS OF TURNING TURNING METHOD PRECAUTION WHEN TURNING BRAKING METHOD BASIC PRINCIPLE OF BRAKE(FRICTION FORCE) RESTRAINT OF BRAKING EFFECT (INERTIA) BRAKING METHOD COMPARISION OF BRAKING DISTANCE IMPACT WHEN COLLISION WIRING DIAGRAM (EURO2) WIRING DIAGRAM (EURO3) 2 SPECIFICATION ITEM LENGTH×WIDTH×HEIGHT(mm) WHEEL BASE(mm) GROUND CLEARANCE(mm) SEAT HEIGHT(mm) DRY WEIGHT(kgf) PASSENGER ENGINE TYPE PISTON DISPLACEMENT(cc) BORE AND STROKE(mm) STARTING SYSTEM TRANSMISSION TYPE DATA 1, 910×750×1, 090 1, 360 126 755 130 2 OIL-COOLED / AIR- COOLED 4CYCLE 124. 9 56. 0×50. 7 START MOTOR CVT ITEM IGNITION SYSTEM BATTERY CAPACITY FUEL CAPACITY() RESERVE FUEL CAPACITY() TIRE SIZE FR. [. . . ] When replacing head light lamp, stop lame and winker lamp, use only a bulb of rated capacity. Using a lamp exceeding the rated capacity can cause over-discharge of battery and wire burning. If the head light is turned off due to aging while driving at night, it will cause an accident by obstructing driver's view. If the tail light is off while driving at night, it will cause an accident by failure of notice by the other drivers. Check the condition daily. <INSPECTION OF STOP LAMP> Turn a main switch "ON". Check a stop lamp for proper operation by operating the front wheel and the rear wheel brakes, and also a lens for damage or contamination. 27 BULB REPLACEMENT METHOD Be sure to turn a main switch "OFF" prior to replacement of a bulb. After replacement with new bulb, check for proper operation. Remove the headlight bulb. Install in the reverse order of removal. HEADLIGHT BULB : 12V 35/35W HEADLIGHT BULB HEADLIGHT ASSY FRONT WINKER LENS FRONT COVER CAUTION Care is to be taken to avoid leaving fingerprints on a headlight bulb. Failing to observe this may cause early damage of the headlight bulb resulted from concentration of heat. Be sure to wear clean gloves when replacing a bulb. If touched to it with bare hands, clean it with a cloth soaked with alcohol to prevent from early damage. WINKER BULB SOCKET RUBBER COVER REAR WINKER LENS <FRONT / REAR WINKER BULB> Loosen two tapping screws to disassemble a lens. REAR VIEW MIRROR Check the objects at the back are well noticed when seating on a driver's seat, and also mirror for damage or contamination. <HEADLIGHT BULB> Check to see if the switch has a contact problem, before replace the bulb. Loosen 4 washer screw and remove the headlight. Press the socket spring, turn counter clock wise. Press a bulb with a light force and rotate it to counterclockwise to disassemble it. Install in the reverse order of removal. FRONT / REAR WINKER BULB : 12V 10W X 2 FUEL LEAK INSPECTION Check there is no gasoline leakage from fuel tank, hoses, carburetor, etc. 28 MAINTENANCE MAINTENANCE SCHEDULE Perform the Self Inspections Before Operation at each scheduled maintenance period. I : INSPECT AND, CLEAN, ADJUST, LUBRICATE OR REPLACE IF NECESSARY R: REPLACE L: LUBRICATE C: CLEAN FREQUENCY ITEM FUEL LINE THROTTLE OPERATION AIR CLEANER ELEMENT SPARK PLUG ENGINE OIL ENGINE OIL FILTER OIL FILTER SCREEN TRANSMISSION OIL BRAKE FLUID VALVE CLEARANCE (FUEL STRAINER) (CARBURATOR IDLE ROTATION) I I R R C R I I I I I I ×1, 000Km MONTH ODOMETER READING(NOTE1) 1 1 4 6 8 12 12 18 16 24 REMARK I I I I R I R R C I I R I R R C R I I I I I I R I R R C I I I I I I R I R R C R R I R I Apply to EU2 ONLY Apply to EU2 ONLY 29 FREQUENCY ITEM BRAKE SHOE / PAD WEAR BRAKE SYSTEM BRAKE STOP SWITCH HEADLIGHT ADJUSTMENT CLUTCH SHOE WEAR SUSPENSION BOLTS, NUTS, FASTENERS WHEELS / TIRES STEERING HANDLE BEARING DRIVE BELT WEIGHT ROLLER SLIDE PIECE Km MONTH ODOMETER READING(NOTE 1) 1, 000Km 1 4, 000Km 6 8, 000Km 12, 000Km 16, 000Km 12 18 24 REMARK I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I If you do not have the appropriate tools or information to conduct maintenance, or if you feel you are not capable to perform maintenance on this vehicle, contact authorized dealers or repair shops for maintenance and repairs. To ensure safety, inspections and maintenance of these parts must be carried out by dealers, or repair centers. NOTES : (1) At higher odometer readings(16, 000Km), repeat at the frequency interval established here. (2) Service more frequently when riding in unusually wet or dusty areas. (3) Replace every 2 years, or at indicated odometer interval, whichever comes first. Replacement requires mechanical skill. 30 MAINTENANCE PRECAUTIONS The following is an explanation of correct inspection methods, cleaning and parts replacing. Please always refer to this section when wanting to inspect or repair your vehicle. REPLENISHING FRONT / REAR BRAKE FLUID CAUTION Always observe safety rules when performing maintenance on the vehicle. Choose a flat surface and make sure the main stand is in a secure down position. [. . . ] Restart the vehicle after 2~3 min when it is turned over. Always turn on the headlight at night. 44 STARTING Prior to starting always look around to avoid accident. Get on the vehicle after pulling back the stand. Start driving slowly after turning on the winker and releasing the brake while ensuring the safety around the vehicle. CAUTION Return the side stand to its original position. [. . . ]