User manual DAELIM S-FIVE

[. . . ] CONTENTS SPECIFICATION OPERATION INSTRUCTION SAFETY PRECAUTIONS PRIOR TO STARTING VEHICLE CORRECT ATTIRE OPERATION CARGO MODIFICATION ATTACHMENT MUFFLER 3 4 4 5 5 6 6 7 7 7 8 10 10 10 11 11 12 12 13 13 13 14 HANDLE BAR LOCK MAIN STAND LOCK SEAT LOCK TRUNK DOCUMENT STORAGE AREA BAG HOLDER BRAKE LOCK LEVER 14 14 15 15 16 16 17 18 18 20 20 22 23 25 26 26 27 28 29 29 30 30 CORRECT DRIVING OPERATION STARTING THE ENGINE IF ENGINE CANNOT BE STARTED AFTER STARTING ENGINE PROPER DRIVING METHODS STOPPING PARTS LOCATION METER READING AND USAGE METER WARNING AND INDICATOR LAMPS SELF INSPECTIONS BEFORE OPERATION INSPECTION OF CONCERNED AREA BRAKE INSPECTION TIRE INSPECTION FUEL CHECK ENGINE OIL CHECK LIGHTS AND WINKER INSPECTION BACK MIRROR INSPECTION FUEL LEAK INSPECTION SWITCH OPERATION MAIN SWITCH STARTER BUTTON HEADLIGHT WINKER SWITCH HORN BUTTON HAZARD SWITCH EQUIPMENT USAGE 1 30 31 REGULAR INSPECTION SCHEDULE 31 SIMPLE MAINTENANCE 33 BRAKE LEVER ADJUSTMENT 33 REAR BRAKE SHOE INSPECTION 34 REPLENISHING BRAKE FLUID 34 BRAKE HOSE, PIPE LEAKAGE, DAMAGE, ASSEMBLY STATE 35 BRAKE PAD INSPECTION 35 REPLENISHING ENGINE OIL 36 TRANSMISSION OIL INSPECTION 37 TIRE PRESSURE INSPECTION 37 WHEEL REMOVAL 38 SIDE STAND INSFECTION 39 SPARK PLUG 40 BATTERY INSPECTION 41 FUSE REPLACEMENT 42 BULB REPLACEMENT 43 AIR CLEANER ELEMENT INSPECTION 45 CABLE RUBBER PART INSPECTION 46 NOTABLES FOR CAR WASHING 46 STORAGE GUIDE 46 47 FRAME AND ENGINE NUMBER LICENSE PLATE INSPECTION SAFE DRIVING PREPARATION BEFORE DRIVING DRIVING METHOD DRIVING POSITION PRECAUTION WHEN DRIVING STARTING 48 48 49 49 51 52 54 54 54 55 56 57 58 58 58 59 59 59 60 REGULAR INSPECTION TURNING METHOD PRINCIPLE OF TURN EFFECT OF SPEED 3 POSITIONS OF TURNING TURNING METHOD PRECAUTION WHEN TURNING BRAKING METHOD BASIC PRINCIPLE OF BRAKE(FRICTION FORCE) RESTRAINT OF BRAKE EFFECT (INERTIA) BRAKING METHOD COMPARISION OF BRAKING DISTANCE IMPACT WHEN COLLISION WIRING DIAGRAM 2 SPECIFICATION ITEM LENGTH WIDTH HEIGHT(mm) WHEEL BASE(mm) GROUND CLEARANCE(mm) SEAT HEIGHT(mm) DRY WEIGHT(kgf) PASSENGER ENGINE TYPE PISTON DISPLACEMENT(cc) BORE AND STROKE(mm) STARTING SYSTEM TRANSMISSION TYPE DATA 1, 795 698 1, 114 1, 260 131 765 94 2 AIR COOLED 2 STROKE 49. 5 ITEM IGNITION SYSTEM BATTERY CAPACITY FUEL CAPACITY( ) OIL CAPACITY( ) TIRE SIZE FR. BRAKE RR. DATA C. D. I 12V3AH(MF TYPE) 6. 0 1. 2 120 / 70 - 12 58L 130 / 70 - 12 62L TELESCOPIC UNIT SWING OIL DAMPER HYDRAULIC DISK DRUM BRAKE B8HSA 7 39. 0 41. 4 START MOTOR / KICK V - MATIC SPARK PLUG FUSE(A) 3 OPERATION INSTRUCTION SAFETY PRECAUTIONS This manual describes matters pertaining to correct operation, safe operation and simple maintenance of the vehicle you purchased. To ensure more comfortable and safer operation, make sure to read this manual carefully prior to operation. The photographs and drawings shown in this manual may differ from those of actual vehicles due to changes in vehicle specifications and modifications made. [. . . ] Conduct engine maintenance with the engine key out of the ignition. Be careful around the engine and muffler when performing maintenance as these areas can become extremely hot. After self maintenance, the waste material must be packed in the specified container and entrusted disposal to the authorized disposal company. BRAKE LEVER ADJUSTMENT REAR BRAKE Brake lever free play is adjusted by rotating the adjuster of the brake arm. After adjustment, check the brake lever to ensure that the clearance is not above or under the prescribed amount. BRAKE LEVER FREE PLAY : 10~20mm CAUTION After adjusting the brake, make sure that " " part of the adjuster contacts the pin as in the drawing below. Brake clearance can change when driving if this is not done. It is not necessary to adjust the front brake. If the brake lever free play is significantly decreased, check the front/rear brake pads and the lining. 33 REAR BRAKE SHOE INSPECTION After adjusting the brakes, check the wear of the brake shoe. While tightly squeezing the rear brake lever, if the " " mark of the brake arm is alined with the " " mark of the brake panel, this indicates that the brake shoe is worn. Please take the vehicle to a service center for repair. REAR BRAKE REPLENISHING BRAKE FLUID 1. Clean dust and other foreign materials around reserve tank to prevent foreign materials from falling inside tank. Remove the screws and take oil cup cap, diaphragm plate, diaphragm off. Replenish recommended brake oil to the upper level inside reserve tank. RECOMMENDED BRAKE OIL IS DOT 3 or DOT 4 4. Reinstall the diaphragm, diaphragm plate, and oil cup cap. Check the brake pads for wear when refilling with brake fluid. A low fluid level may be due to wear of the brake pads. If the brake pads are not worn and the fluid level is low, check for leakage. CAUTION If the vehicle becomes worn-out, the replacement cycle of shoe may differ depending on the wear condition of the rim drum. 34 CAUTION When adding brake fluid, be very careful not to allow foreign materials to enter the reserve tank. Foreign materials can clog the system, causing a reduction or complete loss of braking ability. This can cause brake fluid to leak out of the reserve tank. Do not let brake fluid contact vehicle parts as this damages painted areas. If oil contacts parts, quickly clean the fluid off using a dry cloth. Use recommended brake fluid as other types can undergo chemical changes. If brake fluid is exceedingly low, this can be indication of damage to the brake system. [. . . ] Do not drive excessively long distance and take enough break. If any abnormality is found, stop driving and contact service center to inspect the vehicle. Restart the vehicle after 2~3 min when it is turned over. Always turn on the headlight at night. 51 STARTING Prior to starting always look around to avoid accident. < SCOOTER > Lock the rear brake with the main stand erected. Start the engine using the cell or kick. [. . . ]