User manual DAEWOO CM19102

[. . . ] 19" COLOR TELEVISION OWNER'S MANUAL CM19102 Customer Support: 1-800-270-4535 www. curtismathes. com CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION The AC power cord provided with this product is polarized (one blade wider than the other). To provide power to the TV, insert the AC plug into a standard 120V 60Hz polarized outlet. NOTE Never connect the plug to an electrical source other than one providing 120V 60Hz power. [. . . ] To do this, you will need to switch from the `TV' input to the ` Line ` Input, as follows. 1 With the TV on, press the MENU button twice, then " Set-Up " menu will appear. 2 Use the VCHW buttons to select " Input ". 3 Press the CVOLB buttons to change from `TV' to ` Line `. 4 Wait 10 seconds, or press the MENU button to return to normal TV viewing. 1 2 3 Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Input : TV Select Adjust Next Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Input : TV Select Adjust Next Set-Up Language : Input : English Line Select Adjust Next When connecting an Video/Audio cable from the Video/Audio out jack on the VCR to the Video/Audio in jack on the front of your TV, and your TV's back panel at the same time, the former takes precedence over the latter. 14 Chapter 3 : Operating Your TV Adjusting Video Settings You may wish to adjust the video settings (e. contrast or color) to obtain the most pleasing picture. To do so, follow these directions: 1 With the TV on, press the MENU button, then "Video" menu will appear. 2 The "Settings" item will be selected. Use the CVOLB buttons to turn Settings to Preset or Custom. 3 Use the VCHW buttons to select the video setting you wish to adjust. Descriptions of the video settings are on the next page. 4 Use the CVOLB buttons to adjust the video setting to the level you prefer. 5 Use the VCHW buttons to select another video setting to adjust. 6 When you are finished, press the MENU button until menu disappears. 1 2 3 Video Settings : Contrast Brightness Sharpness Color Tint Select Adjust Video Custom Settings : Contrast Brightness Sharpness Color Tint Select Adjust Video Preset Settings : Contrast Brightness Sharpness Color Tint Select Adjust Preset Next Next Next 4 5 6 Contrast Brightness Chapter 3 : Operating Your TV 15 Returning to the factory settings If you would like to return to the original video settings, as they were calibrated at the factory, follow these steps : 1 With the TV on, press the MENU button, then "Video" menu will appear. 2 Press the CVOLB buttons to set the "Settings" to `Preset'. The TV will remember the `Custom' settings you had previously chosen. When you set "Settings" to `Custom' again, your previous custom settings will be restored. 1 2 Video Settings : Contrast Brightness Sharpness Color Tint Select Adjust Video Custom Settings : Contrast Brightness Sharpness Color Tint Select Adjust Preset Next Next Descriptions of video settings The contrast setting controls the relation between the light and black areas of the screen. If the light areas are too bright and are losing details, press the CVOL button; if the picture is gray and lacks contrast, press the VOLB button. The brightness setting controls the overall amount of light in the picture. If the picture is too bright, press the CVOL button; if the picture is too dark, press the VOL B button. Sharpness controls how the TV displays edges of objects on-screen. If the TV shows multiple vertical lines at the edges of an object, press the CVOL button; if the vertical edges of on-screen objects are fuzzy, press the VOLB button. [. . . ] · Make sure there is nothing blocking the remote control signal. 24 Chapter 6 : Troubleshooting REMOTE CurtisMathes ORIGINAL REMOTE CONTROL Please call 1-800-270-4525 to order a replacement CurtisMathes original remote control. Exact replacement of your original remote control will allow access to all the features of this product. UNIVERSAL REMOTE CONTROLS Optionally, you may desire to purchase a universal remote control available at most electronics Super Stores including Kmart. Please see compatibility chart below with remote control codes for the different categories of CurtisMathes video products. [. . . ]