User manual DAEWOO DP-42GP

[. . . ] This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. - Reorient or relocate the receiving antenna. [. . . ] Normal Normal INPUT SELECT POWER Move Previous Select 2 DISPLAY ZOOMZOOM+ Press the / Button. · After selecting [Picture] by the / buttons, press the button that will display the following. Picture Mode Brightness Contrast Sharpness Color Temp. Normal Normal VOL VOL Sound Screen Utility Input MENU Move Previous Adjust VOL VOL 3 Select the Custom Mode. · Select [User] by the / Picture Sound buttons. User Mode Brightness Contrast Sharpness Color Temp. VOL PICTURE SCREEN MODE FREEZE MODE VOL Screen Utility Input Normal SOUND MUTE MODE SLEEP Move Previous Adjust 20 4 Select User Mode Adjustments · While you are in [Picture Mode ­ User], press the select a specific adjustment item. Picture Sound Screen Utility Input Mode Brightness Contrast Sharpness Color Temp. Normal Normal / buttons to VOL VOL Move Previous Adjust 5 Picture Condition Adjustments · Press the / preference. Picture Sound Screen Utility Input buttons to adjust the picture of your VOL VOL Mode Brightness Contrast Sharpness Color Temp. User Normal Move Previous Adjust NOTES: While you are in the PC INPUT mode, you can only adjust brightness, contrast, sharpness and colour temperature. When you adjust Brightness, Contrast, Colour, Tint in the PC mode, the picture is adjusted finely. The adjusted Values are memoried in each mode seperately. 21 Adjusting Screen Size Adjusting Screen Size · You can adjust screen size or aspect ratio as desired. 1 POWER Press the SCREEN MODE Button. · Each time you press the SCREEN MODE button on the Remote Control, a different SCREEN MODE appears. The sequence used is as follows: · The MENU shown below will display on the screen. SCREEN MODE 1) Component 1 select and DVD Input. 16:9 Panorama INPUT SELECT Normal Enlarge LBS Enlarge LB 2) Component 1 select and DTV Input. DISPLAY ZOOMZOOM+ 16:9 3) PC select. Normal MENU H. Size NOTES: VOL VOL PICTURE SCREEN MODE FREEZE MODE SOUND MUTE MODE SLEEP When the INPUT SIGNAL is DTV [COMPONENT 1 ], only the aspect ratios of 16:9 and 4:3(Normal) will be applied by Input signal. Etc) If input signal is 16:9, PDP displays in 16:9 mode. The digital broadcasting (720p, 1080i) is fixed at the aspect ratio of 16:9. Displaying a picture in a normal mode (4:3) for a long time may cause phosphor of the PDP to be burned. So avoid displaying a picture in a normal mode for a long time. 16:9 : Theatre-like 16:9 picture formats Panorama : 16:9 picture formats with panorama effect Normal : Displays pictures of normal size (i. e. , a 4:3 aspect ratio) Enlarge LB : Enlarges the screen as to fill the black part of up and down, top and bottom of the picture. Enlarge LBS : Enlarges the screen, and shifts up as to see the subtitles in case you are watching video with subtitles. 22 1 Press the MENU Button. · Press the [MENU] button on the Remote Control. Adjusting from MENU Screen MENU Picture Sound Screen Utility Input Mode Brightness Contrast Sharpness Color Temp. Normal Normal Move Previous Select 2 Select "Screen". · Press the Channel Picture Sound / buttons to select "Screen. " H. Position Phase Frequency VOL VOL Screen Utility Input Move Previous Adjust 3 Select the Screen Size. · Press the Volume / Picture Sound buttons to select "Screen Size". H. Position Phase Frequency VOL VOL Screen Utility Input Move Previous Adjust 23 Adjusting Screen Position and Size Adjusting Screen Position and Size · You can adjust the screen position and size as desired. · This function is only used when adjusting the screen position and size on the PDP monitor by using the PC input signal. 1 Press the MENU Button. · The MENU screen as shown below will appear. MENU Picture Sound Screen Utility Input Mode Brightness Contrast Sharpness Color Temp. Normal Normal Move Previous Select INPUT SELECT POWER DISPLAY ZOOMZOOM+ 2 Press the / Button. / Picture Sound · Press the buttons to select `Screen'. H. Position Phase Frequency VOL MENU VOL Screen Utility Input Move Previous Adjust VOL VOL PICTURE SCREEN MODE FREEZE MODE 24 3 Press the Volume / Buttons. · Press the Volume / buttons to select "Screen". · While you are in `Screen' mode, press the or button to select a desired item, and then, adjust the value by pressing the or . VOL Picture Sound Screen Utility Input H. Position Phase Frequency VOL Move Previous Adjust NOTES: Horizontal/Vertical size and position values can be adjusted only in the [PC] input mode. Size: As the value increases, the screen width increases V. Size: As the value increases, the screen height increases. [. . . ] · To cancel the SLEEP TIMER, press the [SLEEP] button to select `OFF'. SLEEP INPUT SELECT Sleep Timer Off DISPLAY ZOOMZOOM+ Sleep Timer Off Sleep Timer 120 Minutes MENU Sleep Timer 15 Minutes Sleep Timer 90 Minutes Sleep Timer VOL VOL 30 Minutes Sleep Timer 60 Minutes PICTURE SCREEN MODE FREEZE MODE NOTES: On-screen information disappears if you do not take any action for about two seconds after pressing the SLEEP button. If you turn the Monitor off after setting SLEEP, the setting is erased. SOUND MUTE MODE SLEEP 34 Before Requesting Service Before requesting for a service, check the following points once again. St yo mm ps · Remote control does not function properly. · Check for any obstacle between the Remote Control and the Display. · Check for dead batteries and incorrect battery orientation. · Check if the Remote Control is the right one. [. . . ]