User manual DAEWOO DSP-HG10

[. . . ] INSTRUCTION MANUAL DSP-HG10 PLASMA MONITOR (DISPLAY) WALL HANGER UNIT H A N G E R U N I T W A L L Thank you for purchasing the Daewoo Electronic Plasma Display Wall Hanger Unit. This wall unit is specifically designed for use with the Daewoo Plasma Display (DSP-4210GM). [. . . ] IMPORTANT SAFETY INSTRUCTIONS PLEASE FOLLOW THESE INSTRUCTIONS FOR YOUR SAFETY PLEASE KEEP THESE INSTRUCTIONS FOR YOUR SAFETY AND TO PREVENT ANY DAMAGE TO THIS UNIT. WARNING : Disregarding these instructions can result in serious injury. WARNING CAUTION CAUTION : Disregarding these instructions will result in the mistreatment of the unit and can result in injury or damage to the unit. * PLEASE CONSULT AN AUTHORIZED SERVICE CENTER TO INSTALL THE WALL HANGER UNIT To install the wall hanger unit, please consult an Authorized service center first. The wall hanger unit needs to be installed securely enough to handle earthquakes or lengthy periods of vibration. (Failing to do so may cause the unit to fall and break) (Failing to do so may cause the unit to fall and break) When assembling, do not use any parts other than those enclosed and secure all parts tightly. Do not leave out any part when assembling. Please install all parts to where indicated. (Failing to do so may cause the unit to fall and break) (Failing to do so may cause the unit to vibrate and to fall) Do not alter or modify any parts Do not use the wall hanger unit with other products. This wall hanger unit (HSP-HG10) is specifically designed to fit the Daewoo Plasma Display (DSP-4210GM). (Failing to do so may cause the unit to fall and break) (Failing to do so may cause the unit to fall and break) 3 PLASMA DISPLAY HANGER UNIT * PLEASE FOLLOW THESE SAFETY PRECAUTIONS WHEN INSTALLING OR HANDLING Special care is needed when installing onto the wall due to its weight (35Kg) When installing, please wear working gloves. When installing on a concrete wall Please be sure to use the enclosed concrete anchors. (If done with bare hands, it may result in injury) Be sure that no one is around to distract you during the installation process. When installing on a wooden wall take special care as the unit may require extra support to uphold the weight of the plasma display. (It may result in injury to you or others) When installing, please have at least two people. Please choose a wall that is straight so that the plasma display can be securely attached onto the wall. H A N G E R U N I T W A L L (Because of its weight, the unit may fall and can cause injury) Place a protective covering over the surface you will be working on when handling the plasma display and the wall hanger units. (If attached on an unstable wall, the unit can fall and break) After installing, please be sure to check to see if the unit has been secured firmly. (Failing to do so may result in unwanted marks on the unit) 4 * PLEASE FOLLOW THESE SAFETY PRECAUTIONS WHEN INSTALLING OR HANDLING When installing, please use the size referenced below to choose a place, and attach the paper pattern plan to the wall. 527. 5 527. 5 328 324 Paper pattern plan . Measurement unit : mm It is important to use the paper pattern plan to choose the proper place; otherwise, it can result in damage to the wall and you will not be able to install the unit When installing, please allow at least 15 cm at the top, bottom, left and right on the wall, and clear all items away from where the unit will be. 15cm 15cm 15cm If proper spacing is not allowed, it may cause the plasma display to overheat, which can cause fire or damage to the unit 15cm 5 PLASMA DISPLAY HANGER UNIT 3. ASSEMBLING INSTRUCTIONS PREPARATION WHEN THE PLASMA DISPLAY IS ATTACHED TO THE STAND 1 TO DETACH THE STAND FROM THE PLASMA DISPLAY . To avoid unwanted marks on the unit, place a protective covering over the surface you will be working on and lay the plasma display as shown below. . Unscrew the secured 2 screws completely and Pull the stand away from the plasma display to detach. 2 TO PLACE THE PROTECTIVE CAPS . There will be two holes where the stand has been detached. . Put the protective caps on the holes and use the screws to secure tightly. Screws H A N G E R U N I T W A L L Holes Caps 6 INSTALLING THE WALL FRAME SET A ON THE PLASMA DISPLAY 1 HOW TO DISPOSE OF THE PLASMA MONITOR WRAPPER . First discard the wrapping band and raise the top box to open. . Afterwards, dispose of the Styrofoam and remove the vinyl covering. 2 HOW TO INSTALL FRAME SET A ON THE UNIT . To avoid unwanted marks on the unit, place a protective covering over the surface you will be working on and lay the plasma display as shown in the picture below. . Place frame set A on the left and right side of the unit and use the enclosed screws (M5) to secure them tightly. (left and right 4 each) . When securing frame set A to the plasma display, make sure that they match the holes correctly. . If holes are matched incorrectly, installation will not be successful. 7 Note PLASMA DISPLAY HANGER UNIT INSTALLING WALL FRAME SET B AND CONNECTING FRAME 1 INSTALLING WALL FRAME SET B AND CONNECTING FRAME. Frame set B Connecting Frame . Place frame set B on the left and right side of the unit and use the enclosed screws (M5) to secure them tightly. Note . Please be sure to not force an . adjustment when connecting frame set B and connecting frame. Otherwise, it will create problems when connecting to frame set A. 2 ATTACHING PAPER PATTERN PLAN ON THE WALL . Place the enclosed paper pattern plan (actual size) on the wall with glue or tape. . Drill holes on the wall as indicated on the paper pattern plan with a hand drill (power drill) and hammer in the concrete anchors (8) firmly. Paper patter n plan H A N G E R U N I T W A L L Paper pattern plan Hand drill 8 3 INSTALL THE WALL FRAME SET ON THE WALL . Install the wall frame set on the wall by matching the concrete anchors with the holes, then use the wall screws (8) to secure tightly. Pape r patt ern p lan 4 INSTALLING ON THE WALL HELD BY SUPPORTING WOODEN STRUCTURE . If it is not feasible to attach frame set B firmly and completely, due to the distance between the two supporting woods; attach one side of the frame set B firmly to the supporting wood, and use appropriate remaining holes(6) to attach the frame set B to the supporting wooden structures. Pape r patte rn pla n 9 PLASMA DISPLAY HANGER UNIT INSTALLING PLASMA DISPLAY ON THE WALL 1 CONNECTING UPPER PART OF FRAME SET A AND FRAME SET B (X) . Insert the upper part of frame set A (X) to frame set B (Y) as indicated below. Frame set B (Y) Frame set A * At least two people are needed to put these frames together. 2 CONNECTING LOWER PART OF FRAME SET A AND FRAME SET B . Adhere Frame set B to Plasma Display unit, then, take the lower part of Frame set B as pictured below and push the (Z) part up gently then let go to connect. H A N G E R U N I T W A L L (Z) 10 3 TO PROVIDE THE SECUREST FIT . After installing plasma display and wall frame sets, for a more secure fit, secure M5 screws (M5x30) on the (Z) part so that (Z) will not move up and down as shown in the picture below. 11 PLASMA DISPLAY HANGER UNIT 4. [. . . ] . Please retain the two needed when modifying angle adjustment. At least two people are Note 2 THE FIGURES BELOW DISPLAY THE POSSIBLE PLASMA DISPLAY ANGLES. H A N G E R U N I T W A L L 0° 15° 15° 20° 12 [. . . ]