User manual DAEWOO DTQ-3062SC

[. . . ] USER MANUAL HDTV Monitor DTQ-3062SC CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION The AC power cord provided with this product is polarized (one blade wider than the other). [. . . ] Press "CHANNELx/y" buttons. Picture Brightness Contrast Sharpness Color Tint Picture NR 32 60 32 32 32:32 Off Move Adj. Prev. ·When "Picture" mode is selected, its sub-menu appears on the screen. ·Continue to press "CHANNELx/y" buttons, and the entries of this sub-menu turn blue in the sequence as follows : Brightness Contrast Sharpness Color Tint Picture NR ·Select "Picture NR" function by using "VOLUMEC/B" buttons, and then, "On" and "Off" repeat in turn. Press "MENU" button twice. ·Press this button one time, and the menu window appears. Press it again, and you will get the previous status of the menu window. (Menu disappears) 30 Adjusting the Picture Screen to Your Preference LAccording to the user's preference, brightness, contrast, sharpness, color, and tint can be adjusted for each of Video1, Video 2, Video3, COMP1, COMP2, and TV mode. 1. Press "MENU" button. ·Then the screen appears as follows: Picture Brightness: ·Adjusts the degree of brightness or darkness of the whole screen. Move Sel. Exit Contrast: ·Adjusts (controls) the degree of brightness between the objects and background of the picture. x 2. Select "Picture" by using "CHANNELx" button. Picture Brightness Contrast Sharpness Color Tint Picture NR 32 60 32 32 32:32 Off Sharpness: ·Adjusts the shapes of objects in the picture, making them appear softer (blurred) or sharper (clean). Move Adj. Prev. Color: ·Adjusts the degree of color saturation. ·"Picture" mode is selected, and its sub-menu appears. ·Continue to press "CHANNELx/y" buttons, and the selected sub-menu sign changes into a blue bar in the following sequence : Brightness Contrast Sharpness Color Tint Picture NR ·Press the "CHANNELx/y" buttons, and capture "Tint" on the blue bar. Tint: ·Adjusts to produce the proper natural color of objects. 31 CB 3. Adjust "Tint" by using "VOLUMEC/B" buttons. Picture Brightness Contrast Sharpness Color Tint Picture NR 32 60 32 32 32:32 Off ·Press "VOLUMEC" button, and the green tint increases. ·Press "VOLUMEB" button, and the red tint increases. ·To adjust other functions such as brightness, etc. , select the function you want by using "CHANNELx/y" buttons, and adjust the mode as above. Move Adj. Prev. Tint 32:32 CB 4. Adjust "Brightness" by using "VOLUMEC/B" buttons Picture Brightness Contrast Sharpness Color Tint Picture NR 32 60 32 32 32:32 Off ·Press "VOLUMEB" button for the Brightness to increase. ·Press "VOLUMEC" button for the Brightness to decrease. Move Adj. Prev. Brightness 32 5. Press "MENU" button twice. ·Press this button one time, and the menu window appears. ·Press it again, and the previous status of the menu window appears. ·To adjust other functions such as brightness, etc. , select the function by using "CHANNELx/y" buttons, and adjust them by using "VOLUMEC/B" buttons. Picture Move Sel. Exit 32 ADJUSTING THE SOUND Customizing the Audio 1. Press "MENU" button. ·Then, the screen appears as follows : Picture "Balance" LThis function balances the volume between left and right speakers. L"Balance" adjusting screen appears as follows: Sound Mode Balance Center Vol Surround Vol Equalizer Mono 32:32 +10 +10 Move Sel. Select "Sound" menu by using "VOLUMEC/B" buttons. ·Move the cursor to the "Sound" menu by using "VOLUMEC/B" buttons. ·Press "CHANNELx" button. Sound Move Adj. Prev. L"VOLUME UPB" keeps the volume of the right speaker as it is, but decreases the volume of the left one. "VOLUME DOWNC" keeps that of the left one as it is, but decreases that of the right one. Move Sel. Exit Sound Mode Balance Center Vol Surround Vol Equalizer Mono 32:32 +10 +10 ·Then, "Sound" menu and its sub-menu appears. Move Adj. Prev. "Equalizer" LThis function adjusts the range of quality sound of speakers. xy 3. Select "Equalizer" by using "CHANNELx/y" buttons. Sound Mode Balance Center Vol Surround Vol Equalizer ( Mono 32:32 +10 +10 ·Capture "Equalizer" on the blue bar by using "CHANNELx/y" buttons. Move Sel. Prev. 33 CB 4. Select Range of Sound by using "VOLUMEC/B" buttons. Equalizer Center Vol Use "VOLUMEC/B" buttons to Adj. Move Prev. ·"CHANNELx" strengthens the selected range of sound. ·"CHANNELy" weakens the range of sound. [. . . ] Enter the 3-digit component code using the remote control number buttons, (0~9) pointing the remote control toward the component. If a correct code was entered, the component will turn on. (If the component does not turn on, repeat the step 4 using another code. ) 5. Press the "Mode" button, and then, LED lamp will blink three times and go out. [. . . ]