User manual DAEWOO DWC-063R annexe 1

[. . . ] PRECAUTIONS FOR PROPER USE OF AIR CONDITIONER Please observe the following instructions. Operate the Selector Switch to run or stop the unit. - Do not use Main Power Switch or Auxiliary Power Switch to operate unit. Do not stick anything into the air outlet or inlet. [. . . ] Exercise caution when opening the window. Failure to do so many result in personal injury and/or property damage. · Step 7 - Recheck the Entire Installation TOP GUIDE WINDOW KIT FRAME WINDOW SEAL B 0. 28"~0. 39"(7~10mm) WINDOW SEAL A WINDOW SASH Screw (Type C, 2 pieces) WINDOW KIT 'R & 'L Screw (Type D, 2x3=6 pieces) GUIDE LOWER Screw (Type C, 2 pieces) SILL BRACKET(1 piece) Leveling Screw (Type A, 1 piece) OUTER WINDOW SILL WALL SILL Screw (Type B, 2 pieces) 7 NAMES OF MAJOR COMPONENTS 5 1 2 3 7 8 9 4 6 0 q 5 1 2 3 7 4 6 NO 1 2 3 4 5 6 PART NAME CABINET BLADE VERTICAL COOL AIR DISCHARGE GRILLE FRONT PANEL CONTROL AIR INTAKE 8 NO 7 8 9 10 11 PART NAME AIR FILTER FRAME GUIDE TOP FRAME WINDOW KIT SHUTTER WINDOW REMOTE CONTROLLER OPERATION INSTRUCTIONS · DISPLAY MODE DISPLAY · It displays the operating mode. REMOTE SIGNAL RECEIVER TEMP. /TIMER DISPLAY · It displays the temperature and the timer. TEMPERATURE SET · It is the button to set the desired room temperature. The temperature can be set within a range from 16°C (60°F) to 32°C (90°F) by 1°C (1°F) FAN SPEED · Everytime you push this button, It is selected as follow. (Low¡High¡Low) ENERGY SAVE · Whenever you push this button, the cumulative power consumption is decreased. MODE SELECT · Everytime you push this button, It is selected as follow. (COOLING¡TURBO¡FAN¡COOLING) POWER ON/OFF SWITCH · To turn the unit ON, push this button. To turn the unit OFF, push this button again. CAUTION When you turn off the unit with cooling mode, the Fan Still work for about 10 seconds. 9 · REMOTE CONTROL REMOTE SIGNAL TRANSMITTER TIMER/CANCEL · Everytime you push this button, timer is set as follow. (1Hr¡2Hr¡3Hr¡4Hr¡5Hr¡6Hr ¡8Hr¡10Hr¡12Hr¡16Hr¡20Hr ¡24Hr¡CANCEL). After the unit is timed, if this button is pushed, timer is canceled. TIMER/ CANCEL SLEEP SLEEP · SLEEP mode is selected as follow. (L1¡L2¡Cancel) MODE FAN SPEED ENERGY SAVE FAN SPEED · Everytime you push this button, it is selected as follow. (Low¡High¡Low) TEMP MODE · Everytime you push this button, it is selected as follow. After a few seconds, display is changed to current room temperature. 11 FUNCTION FAN MODE MODE MODE OPERATION 1. In this mode, the unit circulate room air. Fan speed can be changed. DISPLAY 1. `FAN' lamp lights. FAN ROOM TEMP . or Push the `MODE' button until `FAN' lamp lights. TEMP TURBO DESIRED TEMP . TIMER COOLING ENERGY SAVE ON/OFF ENERGY SAVE ENERGY SAVE ENERGY SAVE or 1. Desired temperature is changed as follows by pushing `ENERGY SAVE' button. +1°C +1°C -2°C 1. `ENERGY SAVE' lamp lights. FAN ROOM TEMP . Push the `ENERGY SAVE' button. 1hr TURBO TEMP `ENERGY SAVE' ON hr `ENERGY SAVE' OFF DESIRED TEMP . When the `ENERGY SAVE' button is pushed, the fan speed goes to `Low' 3. When the `ENERGY SAVE' function is canceled by pushing `ENERGY SAVE' button once again, the desired temperature is return to the former desired temperature. TURBO MODE MODE MODE 1. [. . . ] The marked rating of the extension cord should be 125V 13A (Min. ). WARNING : To avoid death, personal injury or properly damage due to electrical shock, do not use an extension cord or pinch the power cord. Do not remove the warning tag from the power cord. 17 BEFORE CALLING FOR SERVICE When you find something wrong with your room air conditioner, please carefully check the following items. If you are unable to find the cause of trouble, contact your service dealer. Difficulty · Air conditioner does not operate. Possible Cause · No power to unit. Suggested Solution · Confirm power cord is plugged in. · Verify main power switch (main circuit breaker) or fuse of the unit is good. [. . . ]