User manual DAEWOO GV-H42G

[. . . ] Check for enclosed parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not cover the entire side with the sponge as shown in the picture above. 5mm (2 inch) 2 INSTALLING FIXED BRACKETS TO SPEAKERS . Install fixed brackets to speakers before attaching speakers to plasma display. Fixed brackets Bracket (B) Note Please make sure which side the fixed brackets will be screwed to, considering the left and right side of speakers as shown in the picture to the left. Bracket (A) Bracket (C) Bracket (C) Sponge-attached side 5 PLASMA DISPLAY SPEAKER 3 INSTALLING SPEAKERS TO THE PLASMA DISPLAY . Place a protective covering over the surface you will be working on and lay the plasma display as shown below. S P E A K E R . Take the speakers with fixed brackets to the back of the plasma display. Place the hooks onto the fixed brackets to the squared holes in the back of the plasma display. Hooks . Now tightly secure the hooks with the M4 screws. . Please be sure to secure the screws to avoid any shaking or looseness. Note 6 4 CONNECTING SPEAKER WIRES . Take the speaker wire(2) and use the red cord to connect to and fro (+) inputs, and use the black cord to connect to and fro (-) inputs. Note . Please be sure to connect red cord with (+) and black with (-); otherwise, speakers will not produce clear sounds. . Please retain the left over accessories. . Connecting Clamp Wires: - It is used keeping a speaker wire (A speaker wire is connected the back side of main body) as a ficture. 7 PLASMA DISPLAY SPEAKER INSTALLING SPEAKERS TO ITS OWN STAND OR UNINSTALLING SPEAKERS FROM ITS OWN STAND 1 UNINSTALLING SPEAKERS FROM ITS OWN STAND. Speaker . Please, use a coin to loosen the special screws. Stand S P E A K E R 2 INSTALLING SPEAKERS TO ITS OWN STAND. Please be sure to have the vibration absorbent sponge onto the side of the speaker where the stand will be attached. . Use a coin to secure the special screws (round head screws) tightly. Stand . To avoid loose fitting, please be sure that screws are secured tightly. Otherwise, vibrating or distorted sounds may be produced. Note 8 INSTRUCTION MANUAL GV-H42G PLASMA MONITOR (DISPLAY) WALL HANGER UNIT H A N G E R U N I T W A L L Thank you for purchasing the Gold vision Plasma Display Wall Hanger Unit. This wall unit is specifically designed for use with the Gold vision Plasma Display. To ensure the safe operation of the unit, please read these instructions before installing. TABLE OF CONTENTS 1. Check for enclosed parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjusting angles after installation . . . . . . . . . . . . . . . . 12 *To install the wall hanger unit, Please consult an Authorized service center first. 1 PLASMA DISPLAY HANGER UNIT 1. PLEASE CHECK THE ITEMS SHOWN BELOW FRAME SET A FRAME SET B (2) CONNECTING FRAME (2) CONCRETE WALL ANCHOR (1) M5 SCREWS (20 MM) (8) WALL SCREWS H A N G E R U N I T W A L L (8) PAPER PATTERN PLAN Paper pattern plan (8) M5 SCREWS (30MM) (1) (2) 2 2. IMPORTANT SAFETY INSTRUCTIONS PLEASE FOLLOW THESE INSTRUCTIONS FOR YOUR SAFETY PLEASE KEEP THESE INSTRUCTIONS FOR YOUR SAFETY AND TO PREVENT ANY DAMAGE TO THIS UNIT. WARNING : Disregarding these instructions can result in serious injury. WARNING CAUTION CAUTION : Disregarding these instructions will result in the mistreatment of the unit and can result in injury or damage to the unit. * PLEASE CONSULT AN AUTHORIZED SERVICE CENTER TO INSTALL THE WALL HANGER UNIT To install the wall hanger unit, please consult an Authorized service center first. The wall hanger unit needs to be installed securely enough to handle earthquakes or lengthy periods of vibration. (Failing to do so may cause the unit to fall and break) (Failing to do so may cause the unit to fall and break) When assembling, do not use any parts other than those enclosed and secure all parts tightly. Do not leave out any part when assembling. Please install all parts to where indicated. (Failing to do so may cause the unit to fall and break) (Failing to do so may cause the unit to vibrate and to fall) Do not alter or modify any parts Do not use the wall hanger unit with other products. This wall hanger unit is specifically designed to fit the Gold vision Plasma Display. (Failing to do so may cause the unit to fall and break) (Failing to do so may cause the unit to fall and break) 3 PLASMA DISPLAY HANGER UNIT * PLEASE FOLLOW THESE SAFETY PRECAUTIONS WHEN INSTALLING OR HANDLING Special care is needed when installing onto the wall due to its weight (35Kg) When installing, please wear working gloves. When installing on a concrete wall Please be sure to use the enclosed concrete anchors. (If done with bare hands, it may result in injury) Be sure that no one is around to distract you during the installation process. When installing on a wooden wall take special care as the unit may require extra support to uphold the weight of the plasma display. (It may result in injury to you or others) When installing, please have at least two people. [. . . ] PLEASE CHECK FOR THE ITEMS SHOWN BELOW STAND M5 SCREWS (1) (4) 1 PLASMA DISPLAY STAND 2. IMPORTANT SAFETY INSTRUCTIONS PLEASE FOLLOW THESE INSTRUCTIONS FOR YOUR SAFETY PLEASE KEEP THESE INSTRUCTIONS FOR YOUR SAFETY AND TO PREVENT ANY DAMAGE TO THIS UNIT. WARNING : Disregarding these instructions can result in serious injury. WARNING CAUTION CAUTION : Disregarding these instructions will result in the mistreatment of the unit and can result in injury or damage to the unit. When assembling, be sure to use the enclosed parts and make sure all parts are tightly screwed. When assembling, do not alter or modify any parts (If screws come loose, it can result in an electric shock and unwanted accident) When installing, be sure to have at least two people handling the unit. (Doing so may cause the unit to fall and break) When attaching stand to plasma display, be sure to cover the surface to protect from accidental damage. (If the unit is dropped, it may result in damage to the unit and injury to your person) (It may result in unwanted marks on the units, if working without the protective covering) S T A N D 2 3. ASSEMBLING INSTRUCTIONS 1 HOW TO DISPOSE OF THE PLASMA MONITOR WRAPPER . First dispose of the wrapping band and raise the top box to open. . Afterwards, dispose of the Styrofoam and remove the vinyl covering. 3 PLASMA DISPLAY STAND 2 ASSEMBLING THE PLASMA DISPLAY STAND . Open and take out the stand from the box and remove wrapper. . Slide the stand under the plasma display like the picture below. . Use the enclosed 4 M5 screws to secure the assembled stand. [. . . ]