User manual DAEWOO KOR6LBRR
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual DAEWOO KOR6LBRR. We hope that this DAEWOO KOR6LBRR user guide will be useful to you.
Lastmanuals help download the user guide DAEWOO KOR6LBRR.
Manual abstract: user guide DAEWOO KOR6LBRR
Detailed instructions for use are in the User's Guide.
[. . . ] Com manuals search engine
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
(a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary: (1) Interlock operation, (2) Proper door closing, (3) Seal and sealing surfaces (arcing, wear, and other damage), (4) Damage to or loosening of hinges and latches, (5) Evidence of dropping or abuse. (c) Before turning on microwave power for any service test or inspection within the microwave generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections. (d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner. [. . . ] 1 PP POM SW-3
Q'TY 1 1 1 1 1 1 1 1
(1) Remove the gasket door from the door painting as. Method to reduce the gap between the door seal and the oven front surface. (1) To reduce gap located on part âAâ â¢ Loosen two screws on the stopper hinge top, and then push the door to contact the door seal to the oven front surface. (2) To reduce gap located on part âBâ â¢ Loosen two screws on the stopper hinge under, and then push the door to contact the door seal to the oven front surface. (3) To reduce gap located on part âCâ â¢ Loosen the screw on the interlock switch assembly located the top of the oven body. Â¢ Draw the interlock switch assembly inward as possible to engage with the hook on the door bottom. (4) To reduce gap located on part âDâ â¢ Loosen the screw on the interlock switch assembly located the bottom of the oven body. NOTE :A small gap may be acceptable if the microwave leakage does not exceed 4mW/cm2. 7 ABS SG-076D SG-175
Q'TY 1 1 1 3 1 1 1
(1) Remove the screw which secure the control panel, push up two snap fits and draw forward the control panel assembly. (2) Remove three screws which secure the PCB assembly to control panel. (5) Remove the membrane, lever door open, spring button and button door open from the control panel. 1) Remove the screw which secure the grounding ring terminal of the H. NOTE : Never install the magnetron without the metallic gasket plate which is packed with each magnetron to prevent microwave leakage. Whenever repair work is carried out on magnetron, check the microwave leakage. It shall not exceed 4mW/cm2 for a fully assembled oven with door normally closed. Com manuals search engine
INTERLOCK MECHANISM AND ADJUSTMENT
The door lock mechanism is a device which has been specially designed to completely eliminate microwave radiation when the door is opened during operation, and thus to perfectly prevent the danger resulting from the leakage of microwave. replace (NOTE 1)
Check continuity of primary winding of low voltage transformer
0â¦or infinite Approx. 310~420 (normal)
Defective low voltage transformer
Disconnect one side of the lead wire connected form high voltage transformer to the high voltage capacitor and operate the unit
Defective high voltage capacitor
Fuse again blows
Defective high voltage transformer
Downloaded from www. Com manuals search engine
CONDITION Outlet has proper voltage Fuse does not blow. CHECK
RESULT No Continuity
CAUSE Defective magnetron
Check continuity of magnetron
Check continuity of power supply cord
Open power supply cord
Defective touch control circuit
Display do not shown countdown
Malfunction of secondary interlock switch
NOTE 1 All these switches must be replaced at the same time, please refer to âInterlock Mechanism And Adjustmentâ. (TROUBLE 2) Display shows all figures selected, but oven does not start cooking, even though desired program and time are set and the START pad is touched. Voltage being supplied to RELAY (RY2) coil
Defective touch control circuit
Approx. [. . . ] (2) A normal capacitor will show continuity for a short time, and then indicate 10Mâ¦once the capacitor is charged. High voltage diode
(1) Isolate the diode from the circuit by disconnecting the leads. (2) With the ohmmeter set on the highest resistance scale measure the resistance across the diode terminals. Meter with 6V, 9V or higher voltage batteries should be used to check the front-back resistance of the diode, otherwise an infinite resistance may be read in both directions. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE DAEWOO KOR6LBRR
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DAEWOO KOR6LBRR will begin.