User manual DAEWOO S144N-RH [PLVCP]

[. . . ] VIDEO CASSETTE PLAYER MODEL NO. :PLVCP OPERATING INSTRUCTIONS BEFORE OPERATING THIS UNIT, PLEASE THOROUGHLY READ THIS MANUAL, AND RETAIN IT FOR FUTURE REFERENCE. · AN IN DE ETY AF NDENT LABO PE R This instrument is listed by Underwriter's Laboratories, Inc. It is designed and manufactured to meet rigid U. L. safety standards against X-radiation, fire, casualty and electrical hazards. Y · TEST TOR IN RA OR PUBLIC S GF DRAWING YOUR ATTENTION Thank you purchasing this VCP, developed to provide advanced features and functions for high quality performance. To obtain the best results and to avoid malfunction, PLEASE CAREFULLY READ THE DESCRIPTIONS AND OPERATING PROCEDURE CONTAINED IN THIS OWNER'S MANUAL PRIOR TO OPERATING THIS VCP. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] The FF indicator lamp will light up in orange. *Cassette-In lamp When the cassette is inserted, the CST-IN lamp will light up in red. (DEW lamp This indicator will flash (if power is on) to indicate excessive moisture has been inside of VCP. This unit will not operate until it dries out sufficiently (the tape can be ejected from the unit). When DEW mode has been activated, leave the unit on to allow it to dry out completely. 11 IDENTIFICATION (continued) REAR PANEL !FUSE HOLDER This main line fuse is accessible with the external fuse holder simply by unscrewing the cap. If the main line fuse should blow then replace the fuse with a proper rated fuse (125V, 2A). @RF OUT CHANNEL SELECTION SWITCH Set to channel 3 or 4, whichever is not being broadcasted in your area. #ANT. IN Connect the TV antenna to this terminal. 12 IDENTIFICATION (continued) $VIDEO OUT Connect this terminal to VIDEO IN terminal of your television, using the RCA cord provided. %AUDIO OUT L/R Connect this terminal to AUDIO IN terminal of your television, using the RCA cord provided. ^DIN JACK 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN S. STATUS DATA OUT GND EXT. REMOTE DATA. IN GND GND LEFT RETURN 6 PIN 7 PIN 8 PIN 9 PIN GND RIGHT RETURN VIDEO OUT AUDIO LEFT AUDIO RIGHT &RF OUT Connect this terminal to antenna terminal of your television on using the coaxial cable. *( DC JACK IN Connect this jack to DC source (DC 12V). NOTE : This VCP is for 12V use only, so do not use it in 24V vehicles. If you use this set in a 24V vehicle, all the indicator lamps will blink. To avoid the malfunction of this set, please disconnect the plug from the power source. 13 IDENTIFICATION (continued) REMOTE CONTROL OPERATION RANGE 1. Any object between the remote control and VCP will block the path of beam when it is being used. Dark walls, direct sunshine or very bright (incandescent) light will reduce the remote control sensitivity. Hold the remote control within an angle range of about 30º from either side of the remote sensor center as shown. 7m 30 o 30 o 3. When the remote control is vertical to the remote Sensor, it will work within about 23feet (7m) from the VCP. Point the front of the remote control directly at the front of the VCP. 14 IDENTIFICATION (continued) BATTERY INSTALLATION 1. Remove the battery cover on the reverse side of the remote control. Install 2 batteries ("AAA" size) into the remote control. (Carefully install batteries to match the polarity diagrams) 3. · It is advisable to take batteries out of the remote control when it is not in use for a long time. 15 IDENTIFICATION (continued) REMOTE CONTROL BASIC FUNCTIONS POWER RE-PLAY TRACKING -/+ PLAYBACK REWIND/REVIEW STOP PAUSE / STILL FRAME RETRACKING FAST FORWARD / CUE 16 IDENTIFICATION (continued) WHEN YOU USE THE REMOTE CONTROL · Do not press two keys at the same time. · Do not expose the remote sensor to the sunshine. · It causes the VCP not to operate. [. . . ] Operation key does not work. Cassette is ejected upon inserting. Audio output does not change to Hi-Fi · The cassette is recorded in mono mode. · The first autotracking is executing until now. 26 SYMPTOMS No backlighting at power button. CAUSE · No 12V DC. POSSIBLE SOLUTIONS · Check circuit fuse at source of power (see vehicle/converter manual). · In-line fuse of power cord (in lighter plug). · VCP (2 amp* 20X 5mm) fuse located on rear of unit. [. . . ]