User manual DAHON JETSTREAM EX 2009

[. . . ] It is important to completely understand the operation of your bicycle's brake system. Improper use of your bicycle's brake system may result in a loss of control or an accident, which could lead to severe injury. Because each bicycle may handle differently, be sure to learn the proper braking technique (including brake lever pressure and bicycle control characteristics) and operation of your bicycle. [. . . ] This can be done by consulting your professional bicycle dealer and the bicycle's owners manual, and by practicing your riding and braking technique. These brake levers are equipped with a mode switching mechanism to make them compatible with cantilever brakes and Roller Brakes or V-Brakes with power modulator. SI-6FD0A SL-8S20 BL-IM65 CJ-8S20 Revo-shift Lever Brake Lever Cassette Joint Disconnecting the shifting cable when removing the rear wheel from the frame Disconnect the cable from the cassette joint when removing the rear wheel from the frame. Installation of the shifting cable Use a shifting cable with one inner cable drum. the SIS-SP40 5. Pass the inner cable throughthe plastic cap. Turn the cable 60 to the hook. Hook counterclockwise and attach it Adjusting the cassette joint Revo-shift lever to 4 . Set theto be sure that the yellow setting lines on Check the cassette joint bracket and pulley are aligned at this time. Yellow setting lines (Lever side) LOCK Cable with one inner cable drum / SIS-SP40 (4 mm dia. ) Aluminum cap Plastic cap Technical Service Instructions 20 8S CJ- N JA PA 1. Set the Revo-shift lever to 1 . Set to 1 If cutting the outer casing, cut it near the end with the plastic cap while the cap is still attached. Then make the cut end perfectly round and attach the plastic cap. Turn the cable 60 CJ-8S20 JAPAN Set to 4 Plastic cap slit in the cassette joint bracket, and then insert the end of the outer casing securely into the outer casing holder. The yellow setting lines on the cassette joint are located in two places. If you try to force operation of the shifting lever while the pedals are being turned strongly, your feet may come off the pedals and the bicycle may topple over, which could result in serious injury. Tightening torque: 2 ­ 2. 5 N·m {20 ­ 25 kgf·cm} Recess in winder unit Half grip Clamp bolt CJ-8S20 JAPAN 4. Replace the upper cover and tighten the cover fixing screw. Tightening torque: 0. 1 ­ 0. 2 N·m {1 ­ 2 kgf·cm} Cover fixing screw Gap in pulley Inner cable fixing nut Upper cover Guide CJ-8S20 JAPAN CJ-8S20 JAPAN Guide 1 Turn the pulley OK Not OK These service instructions explain how to use and maintain the Shimano bicycle parts which have been used on your new bicycle. For any questions regarding your bicycle or other matters which are not related to Shimano parts, please contact the place of purchase or the bicycle manufacturer. Pulley hole Pulley the cable 10. to the frame with the outer casing 10 cm 10 cm 15 cm ® NOTE: Tighten 22. 2 mm 5 mm Allen key 2 mm Allen key or #14 spoke For maximum performance we highly recommend Shimano lubricants and maintenance products. Parts are not guaranteed against natural wear or deterioration resulting from normal use. Grip Tightening torque: 6 ­ 8 N·m {60 ­ 80 kgf·cm} Note: If reusing the cable, refer to steps 7 to 9 in "Installation of the shifting cable". Outer casing bands CJ-8S20 JAPAN One Holland, Irvine, California 92618, U. S. A. Phone: +1-949-951-5003 Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222 3-77 Oimatsu-cho, Sakai, Osaka 590-8577, Japan C Apr. Printed in Singapore CJ-8S20 JAPAN If the incorrect mode is selected it may cause either excessive or insufficient braking force to occur, which could result in dangerous accidents. Be sure to select the mode in accordance with the instructions given in the table below. CJ-8S20 JAPAN Pedaling becomes heavier Indicator moves toward 8 Indicator outer out from the 2. [. . . ] Printed in Singapore CJ-8S20 JAPAN If the incorrect mode is selected it may cause either excessive or insufficient braking force to occur, which could result in dangerous accidents. Be sure to select the mode in accordance with the instructions given in the table below. CJ-8S20 JAPAN Pedaling becomes heavier Indicator moves toward 8 Indicator outer out from the 2. Pull theholder casingcassette joint, outer then casing of the and remove the inner cable from the slit in the bracket. Bracket Upper cover CJ -8S PA JA 20 Cassette joint side the end casing is 6. [. . . ]