User manual DAIKIN BRC1D527

[. . . ] OPERATION MANUAL Remote controller BRC1D527 1 3 6 23 7 8 9 2 1 10 4 12 14 17 25 11 22 16 13 29 15 18 19 20 21 5 33 24 26 35 27 36 37 28 1 30 31 32 34 2 Start 5s 5s 5s 5s + 5s End 2 BRC1D527 Remote controller Operation manual THANK YOU FOR PURCHASING THIS CONTROLLER. READ THE MANUAL ATTENTIVELY BEFORE USING THE INSTALLATION. AFTER READING THE MANUAL, STORE IT IN A SAFE PLACE FOR FUTURE USE. Before initial operation, contact your dealer to obtain all details concerning your air conditioning installation. 1. [. . . ] 7 LEAVE HOME LEAVE HOME is a feature that enables to keep the room temperature above 10°C when the occupants are out. This function will switch on heating if the installation is switched off. In this mode, the controller will automatically switch between heating and cooling as required by the setpoint or limit temperature. 4 COOLING OPERATION In this mode, cooling will be activated as required by the setpoint or limit temperature. Operation Manual operation In manual operation, the user decides about the settings of the installation. The last setting remains active until the user changes it. As the controller can be implemented for a wide variety of installations and features, it might occur that you select a function that is not available on your installation; if this is the case, the message will appear. In this mode, heating will be activated as required by the setpoint or limit temperature. Hot start (heat pump types only) At the start of a heating operation, the indoor fan is stopped until a certain indoor heat exchanger temperature is reached and is displayed. This prevents cold air from leaving the indoor unit. Operation manual 5 BRC1D527 Remote controller 4PW16770-1 Use the mode. button to select the desired operation Fan only operation Dry operation Automatic operation Cooling operation Heating operation Press the button to toggle between limit operation and the operations listed above. In limit operation, use the button to select minimum and maximum temperature settings. Use the or buttons to adjust the minimum and maximum temperature settings. button to enable or disable the Operation manual 7 BRC1D527 Remote controller 4PW16770-1 What can the schedule timer do? The concept of the schedule timer is simple, straightforward though powerful. The schedule timer can order 3 actions: 1 switch on the installation at a scheduled time, in combination with a setpoint (exact temperature control) 2 switch off the installation (end of control) 3 switch on the installation at a scheduled time, in limit operation The schedule timer can accept a maximum of 5 actions per day. For each day of the week a maximum of 5 actions can be programmed, totalling a maximum of 35 programmed actions. The action that was programmed first for a certain day is action 1, the last programmed action for a day could be action 1 (in case only one action is programmed for that day) to 5. It is of utmost importance to understand that the number assigned to the programmed action, DOES NOT DETERMINE WHEN the programmed action will be executed. Only the TIME, being a part of the data entered when programming the action, will determine when the programmed action will be executed. OR · switch off the installation (the schedule timer remains enabled and reactivates the installation as programmed); the operation lamp will turn off, cool or heat, whichever is required to keep the room temperature within a specified range (limit operation); and are displayed. The schedule timer will change the operation mode in LIMIT operation only. OR · To be able to verify the programmed actions, you can browse the programmed actions, see below. What will the schedule timer NOT do? The schedule timer will not: · control fan speed, · control air flow direction, · control ventilation mode, · control ventilation amount, · change the operation mode for a scheduled setpoint. The parameters listed above can be set manually, without interfering with the schedule timer. More sophisticated remote controllers are available. Consult your dealer for more information. What will the schedule timer do? If enabled, the schedule timer will execute the programmed actions. It will order the installation to: · cool or heat, depending on the current operation, if applicable; the setpoint will be displayed, Browsing the programmed actions in the schedule timer (read-out only) Refer to figure 2. Browsing the programmed actions of the schedule timer is a sequential process. [. . . ] Press the button for 5 seconds; program mode is enabled, the icon and selected action are blinking. Edit the settings using the same buttons described above. Select the "last action" using the button and decide if you do or do not want to copy the programmed action(s) to the next day (pressing the and buttons simultaneously or only the button for 5 seconds). When all data for the schedule timer actions for Monday are entered, you must confirm the programmed actions. Make sure the last schedule timer action you want to keep is selected (schedule timer actions with a higher number will be deleted). [. . . ]