User manual DAIKIN FVXG25K

[. . . ] Com manuals search engine SiBE121135 SUPER MULTI NX E-Series F-Series G-Series K-Series Cooling Only Outdoor Unit 3MKS50E3V1B 4MKS58E3V1B FFQ25B9V1B FFQ35B9V1B FFQ50B9V1B FFQ60B9V1B 4MKS75F2V1B FHQ35BWV1B FHQ50BWV1B FHQ60BWV1B 5MKS90E2V3B FDBQ25B8V1 FBQ35C8VEB FBQ50C8VEB FBQ60C8VEB Indoor Unit FTXS25J2V1B FTXS35J2V1B FTXS42J2V1B FTXS50J2V1B FTXS60GV1B FTXS71GV1B Heat Pump Outdoor Unit 3MXS40K2V1B 3MXS52E3V1B 3MXS68G2V1B 4MXS68F2V1B FVXG25K2V1B FVXG35K2V1B FVXG50K2V1B FVXS25FV1B FVXS35FV1B FVXS50FV1B FLXS25BAVMB FLXS35BAVMB FLXS50BAVMB FLXS60BAVMB FDXS25E7VMB FDXS35E7VMB FDXS50C7VMB FDXS60C7VMB 4MXS80E2V3B 5MXS90E2V3B FCQG35FVEB FCQG50FVEB FCQG60FVEB FFQ25B9V1B FFQ35B9V1B FFQ50B9V1B FFQ60B9V1B FHQ35BWV1B FHQ50BWV1B FHQ60BWV1B FDBQ25B8V1 FBQ35C8VEB FBQ50C8VEB FBQ60C8VEB Indoor Unit FTXG25JV1BW FTXG25JV1BA FTXG35JV1BW FTXG35JV1BA FTXG50JV1BW FTXG50JV1BA CTXS15K2V1B FTXS20K2V1B FTXS25K2V1B CTXS35K2V1B FTXS25J2V1B FTXS35J2V1B FTXS42J2V1B FTXS50J2V1B FTXS60GV1B FTXS71GV1B i Downloaded from www. 1 Safety Cautions Be sure to read the following safety cautions before conducting repair work. The caution items are classified into “ Warning” and “ Caution”. The “ Warning” items are especially important since they can lead to death or serious injury if they are not followed closely. [. . . ] € If you do not like AUTO operation, you can manually select the operation mode and setting you like. 4 Adjusting the Airflow Direction FLXS25/35/50/60BAVMB Adjusting the Airflow Direction You can adjust the air flow direction to increase your comfort. €“ ” is displayed on the LCD and the flaps will begin to swing. When the flaps have reached the desired position, press “SWING button” once more. Com manuals search engine 223 RA Indoor Unit SiBE121135 To adjust the vertical blades (louvers) • When adjusting the louver, use a robust and stable stool and watch your steps carefully. (You will find a knob on the left side and the right side blades. € Unless [SWING] is selected, you should set the flap at a near- horizontal angle in COOL or DRY mode to obtain the best performance. € In COOL or DRY mode, if the flap is fixed at a downward position, the flap automatically moves in about 60 minutes to prevent condensation on it. ATTENTION • Always use a remote controller to adjust the flap angle. If you attempt to move it forcibly with hand when it is swinging, the mechanism may be broken. € Be careful when adjusting the louvers. 5 POWERFUL Operation POWERFUL Operation POWERFUL operation quickly maximizes the cooling (heating) effect in any operation mode. Then the system automatically operates again with the settings which were used before POWERFUL operation. € When using POWERFUL operation, there are some functions which are not available. NOTE Notes on POWERFUL operation • In COOL and HEAT mode To maximize the cooling (heating) effect, the capacity of outdoor unit must be increased and the air flow rate be fixed to the maximum setting. The temperature and air flow settings are not variable. € In FAN mode The air flow rate is fixed to the maximum setting. 6 OUTDOOR UNIT QUIET Operation OUTDOOR UNIT QUIET Operation OUTDOOR UNIT QUIET operation lowers the noise level of the outdoor unit by changing the frequency and fan speed on the outdoor unit. This function is convenient during night. ) • POWERFUL operation and OUTDOOR UNIT QUIET operation cannot be used at the same time. Priority is given to the function of whichever button is pressed last. € If operation is stopped using the remote controller or the main unit ON/OFF switch when using OUTDOOR UNIT QUIET operation, “ ” will remain on the remote controller display. [. . . ] Wipe off the old silicon grease completely on a radiation fin. Apply the silicon grease evenly to the whole. Do not leave any foreign object such as solder or paper waste between the power transistor and the radiation fin, and also the diode bridge, and the radiation fin. Tighten the screws of the power transistor and the diode bridge, and contact to the radiation fin without any gap. [. . . ]