User manual DANBY DKC445BLS

[. . . ] Keg Cooler The model number can be found on the serial plate located on the back panel of the unit. All repair parts available for purchase or special order when you visit your nearest service depot. To request service and/or the location of the service depot nearest you, call the TOLL FREE NUMBER. When requesting service or ordering parts, always provide the following information: · Product Type · Model Number · Part Description Model · Modèle· Modelo DKC445BL For service, contact your nearest service depot or call: 1-800-26- Danby (1-800-263-2629) to recommend a depot in your area. Glacière de bière en fût Le numéro du modèle se trouve sur la plaque d'identification située sur le panneau arrière de l'appareil. En cas de réparation, veuillez contacter votre service après-vente le plus près ou communiquez au: 1-800-26- Danby (1-800-263-2629) pour connaître le service après-vente le plus proche. Il est possible d'acheter les pièces de rechange ou de les obtenir par commande spéciale en vous rendant à votre service après-vente le plus proche. [. . . ] Make sure the "secondary" shut-off valve located on the lower stem pipe of the regulator is in the "closed" position. 11 NOTE: When the secondary valve (handle) is positioned "Horizontal" (east/west) the valve is closed. 1 2 When the secondary valve (handle) is positioned "Vertical" (north/south) the valve is open. To open the main CO2 cylinder valve, (slowly) turn the main valve counter clockwise until fully open. You will notice the needles on both gauges start to climb. Adjusting the CO2 Regulator: There are two pressure gauges on the CO2 regulator. 12 The upper gauge #1 monitors "LOW" (internal keg) pressure and must be adjusted to the correct operating pressure of 10~12psi/lbs. The lower gauge #2 monitors "HIGH" (CO2 cylinder) pressure and is not adjustable. The high pressure gauge also acts as a fuel gauge to let you know when the C02 cylinder needs re-filling. IMPORTANT: The internal operating pressure of the beer keg should be adjusted and maintained between 10 ~ 12psi/lbs. To adjust the "low" pressure gauge; · Using an adjustable wrench, release the adjustment lock nut # 3. 12 · Using a flat screwdriver, turn the regulator adjustment screw # 4 See Fig. 12 Clockwise rotation of the adjustment screw will increase low pressure. Counter clockwise rotation of the adjustment screw will decrease low pressure · When the required operating pressure is attained retighten the adjustment lock nut # 3. · You are now ready to serve cold beer 3 4 Secondary Shut-off Valve 6 5 Fig. 12 7 HOW TO REPLACE AN EMPTY CO2 CYLINDER 1. Close the main cylinder valve (A) by turning in a clockwise direction. Close the secondary shut-off valve (C) by turning to "horizontal" (east/west) position on lower stem pipe. Remove the air line clamp and hose from the regulator. Remove the regulator assembly (E) from empty cylinder. Remove dust cap from new and/or replacement CO2 cylinder 6. Re-attach regulator assembly (E) to new/replacement cylinder. Re-attach the air line hose to regulator (barb connection) and secure with clamp. [. . . ] First Year During the first year (1), any electrical parts of this product found to be defective, including any sealed system units, will be repaired or replaced, at warrantor's option, at no charge to the ORIGINALpurchaser. light bulbs) are not warranted or guaranteed for any length of time. Second Through During the next four years (4) any part of the sealed system found to be defective (consisting of compressor, condenser, evaporator, Fifth Year dryer and all related tubing) will be replaced without charge. The purchaser shall pay for all labour and return freight during this four year (4) period for repair or replacement of any sealed system components. [. . . ]