User manual DANBY DPR2262

[. . . ] Switching the Air Conditioner Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjusting the Air Flow Direction Horizontally . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjusting the Air Flow Direction Vertically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 7 8 9 9 RECOMMENDATIONS FOR USE Power Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature and Humidity Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Possible temperatures: Can be set between 18 C and 29 C. Result: The air conditioner starts cooling if the room temperature is higher than the selected temperature. 3 To control the direction of the air flow, refer to page 9. E-6 Ventilating Your Room If the air in your room is stale, you can ventilate the room using the Fan feature. (Except AAC5040/AAC5040-1) 1 If you wish to discharge stale air, push the ventilation lever on the front of the unit to the right and open position ( ). Result: The air inside the room circulates and stale air is discharged outside. ). Otherwise, push the ventilation lever to the left and closed position ( Result: The air simply circulates inside the room. 2 Turn the operating mode selection dial and set it to "Hi Fan" or "Low Fan" position. Result: The air conditioner starts up in fan mode. You can change modes at any time. 3 To control the direction of the air flow, refer to page 9. E-7 Switching the Air Conditioner Off You can switch the air conditioner off whenever you want. 1 To switch the unit off, simply set the operating mode selection dial to the " OFF " position. Result: The air conditioner stops operating. E-8 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room, you can adjust the orientation of the inner air flow blades on the unit. Adjust the air flow blades to the desired position by sliding them side to side. Adjusting the Air Flow Direction Vertically The outer air flow blades can be adjusted to control the vertical air flow direction. (Except AAC5040/AAC5040-1) RECOMMENDATION When. . . - When the number on the THERMOSTAT control is too high, the room temperature may be too warm. Check to see whether there is an open window or leakage of cool air to the outside. Check to see whether there is any obstacle adversely affecting the flow of the air inside and outside the room. - Remove the obstacle or change the position of the air conditioner. Check to see whether the air filter is clogged with dust or contaminated with foreign substances. Check to see whether there is any direct sunlight facing the air conditioner. Check to see whether there is any electric device generating heat. - Do not use the air conditioner together with any heating device. Ventilate the room. The air comes out smoothly, but cooling is not effective. Odors are permeating the room during air conditioning. E-12 Technical Specifications Design and specifications are subject to change without notice. Model AAC5040/AAC5040-1 Power Supply 115V~, 60Hz E-13 LIMITED AIR CONDITIONER WARRANTY This quality product is warranted to be free from manufacturer's defects in material and workmanship, provided that the unit is used under the normal operating conditions intended by the manufacturer. This warranty is available only to the person to whom the unit was originally sold by Danby or by an authorized distributor of Danby, and is non-transferable. [. . . ] Save as herein provided, Danby Products Limited (Canada) or Danby Products Inc. (U. S. A), shall not be responsible for any damages to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of the unit, the purchaser does hereby agree to indemnify and save harmless Danby Products Limited from any claim for damages to persons or property caused by the unit. GENERAL PROVISIONS No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following: 1) Power Failure. 2) Damage in transit or when moving the appliance. [. . . ]