User manual DANFOSS TP 9

[. . . ] If mounted on a flush mounted box, cables can enter from the rear through the aperture in the wallplate. Whilst the unit does not require an Earth connection, two terminals are provided on the wallplate fot Earth continuity purposes. Locate and fix the Remote Sensor, this should be as per room thermostat i. e. 1. 5m above floor, away from draughts and extraneous heat gains. [. . . ] HP22 or HP28 Motorised Zone Valve with Spring Return Actuator and SPST auxiliary switch. Other Danfoss Randall products suitable for use with the above control circuit:AT Cylinder Thermostat. HP28C Motorised Zone Valve with Spring Return Actuator and SPDT auxiliary switch. Typical fully pumped system with 3 port Mid-position Valve. TP9 (Switch 1 to PUMPED) Terminals Mains Supply HW CH HW CH OFF OFF ON ON Typical fully pumped system with S. R. Z. V. TP9 (Switch 1 to PUMPED) Terminals HW CH HW CH OFF OFF ON ON Typical fully pumped system with F. M. Z. V. TP9 (Switch 1 to PUMPED) Terminals Mains Supply HW CH HW CH OFF OFF ON ON NL123456 NL123456 Mains Supply NL123456 Remote Sensor Cyl. Stat. { N L 3 amp fuse Remote Sensor Cyl. Stat. Remote Sensor { N L 3 amp fuse N Looping Terminals S. R. V. Z in HW Boiler & Pump N Looping Terminals S. R. V. Z in CH F. M. Z. V. in HW N Looping Terminals Boiler & Pump N 3 port midposition valve N Boiler & Pump F. M. Z. V. in CH N N N N N N Other Danfoss Randall products suitable for use with the above circuit:AT Cylinder Thermostat. HS3 Three Port Mid-position Valve with a Spring Return Actuator. Other Danfoss Randall products suitable for use with the above circuit:AT Cylinder Thermostat. 2 x HP22 or HP28 Motorised Zone Valve with Spring Return Actuator and SPST auxiliary switch. fully motorised zone valve. Other Danfoss Randall products suitable for use with the above circuit:AT Cylinder Thermostat. S. R. Z. V. = spring return zone valve. F. M. Z. V. = Ensure Earth continuity throughout, where Earth is required. NOTE: Danfoss Randall manufacture a complete range of domestic heating controls including timeswitches and programmers, room and cylinder thermostats, thermostatic radiator valves, motorised valves and boiler efficiency controls; as well as a comprehensive range of commercial time controls and valves. Ask for our full colour Product Selection Guide. This product complies with the following EC Directives: Electro-Magnetic Compatibility Directive. (EMC) (89\336\EEC), (92\31\EEC) Low Voltage Directive. (LVD) (73\23\EEC), (93\68\EEC) 2 TP9 Electronic Central Heating Controller Programmable Room Thermostat plus Domestic Hot Water Timer USER INSTRUCTIONS General Description The TP9 can have a room temperature setting range of either 5°C to 30°C or 16°C to 30°C. Switch 4 on the back of the module is used to choose which range. In all display diagrams the 5°C to 30°C range is used. The TP9 will control your Central Heating and Domestic Hot Water system in any one of three ways: 1. [. . . ] The selected temperature will last until the next programmed change. A On 6:30AM When the Central Heating is ON, a flame symbol appears in the display and the red CH indicator illuminates. b Off 8:30AM When the Hot Water is ON, a tap symbol appears in the display and the HW indicator illuminates. changing setting 2, in table 1 above, to 3:00PM would also change settings 3 and 4 to 3:00PM. [. . . ]