User manual DATALOGIC MAGELLAN 2200VS

[. . . ] Magellan® 2200VS/2200VS and 2300HS/2300HS Product Reference Guide Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or "Datalogic Scanning"). Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own internal business purposes. [. . . ] Scan the appropriate digits from the keypad in Appendix C that represent the desired Label ID characters; entered as two hex pairs. A table containing the ASCII Character Set and their corresponding Hex Values is available in the inside back cover of this manual. ASCII parameters must be input by scanning a pair of hexadecimal digits for each character. Thus, to set a two-character value of AB, bar codes containing the digits `4', `1', `4', and `2' must be scanned. The selectable range for this option is any hex value from 00 to FF. Complete the programming sequence by scanning the SWITCH bar code. SET UPC-A 128 SUPPLEMENTAL LABEL ID Product Reference Guide 5-131 Programming UPC-E Enable Enables/disables the ability of the scanner to decode UPC-E labels. Scan either the enable or disable bar code below. You'll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. Complete the programming sequence by scanning the SWITCH bar code. UPC-E = DISABLE UPC-E = ENABLE 5-132 Magellan® 2200VS/2200VS and 2300HS/2300HS UPC-E Enable UPC-E Number System Character Transmission Enables/disables transmission of a UPC-E number system character. This item is ignored when the advanced feature, Full Label Edit, is enabled. Scan either the enable or disable bar code below. You'll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. Complete the programming sequence by scanning the SWITCH bar code. UPC-E NUMBER SYSTEM CHARACTER TRANSMISSION = DISABLE UPC-E NUMBER SYSTEM CHARACTER TRANSMISSION = ENABLE Product Reference Guide 5-133 Programming UPC-E Check Character Transmission Enables/disables transmission of a UPC-E check character. This item is ignored when the advanced feature, Full Label Edit, is enabled. Scan either the enable or disable bar code below. You'll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. Complete the programming sequence by scanning the SWITCH bar code. UPC-E CHECK CHARACTER TRANSMISSION = DISABLE UPC-E CHECK CHARACTER TRANSMISSION = ENABLE 5-134 Magellan® 2200VS/2200VS and 2300HS/2300HS UPC-E Enable Expand UPC-E to UPC-A Enables/disables expansion of UPC-E labels to UPC-A. Scan either the enable or disable bar code below. You'll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. Complete the programming sequence by scanning the SWITCH bar code. EXPAND UPC-E TO UPC-A = DISABLE EXPAND UPC-E TO UPC-A = ENABLE Product Reference Guide 5-135 Programming Expand UPC-E to EAN-13 Enables/disables expansion of UPC-E labels to EAN/JAN-13. Scan either the enable or disable bar code below. You'll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. Complete the programming sequence by scanning the SWITCH bar code. EXPAND UPC-E TO EAN/JAN-13 = DISABLE EXPAND UPC-E TO EAN/JAN-13 = ENABLE 5-136 Magellan® 2200VS/2200VS and 2300HS/2300HS UPC-E Enable UPC-E Label ID This feature specifies a UPC-E label ID to be added to bar code data. The programming feature, RS-232 Label ID Control, designates whether the Label ID is transmitted as a prefix or suffix or if Label ID is disabled. Scan the bar code, SET UPC-E LABEL ID below. [. . . ] Label length excluding prefix characters must be 14 characters. Example: ']e001044123456789'. RSS Expanded · · Prefix must be ASCII characters ']e0'. Label length excluding prefix characters must be at least 1 character. Maximum length is the maximum label size supported by the scanner. [. . . ]