User manual DATALOGIC MAGELLAN 8400

[. . . ] Magellan® 8300/8400 Product Reference Guide Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or "Datalogic Scanning"). [. . . ] You'll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. Complete the programming sequence by scanning the SWITCH bar code. SCALE WARM-UP TIME = NO WARM-UP SCALE WARM-UP TIME = 5 SECONDS Product Reference Guide 6-53 Scale Warm-up Time -- continued Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. SCALE WARM-UP TIME = 10 SECONDS SCALE WARM-UP TIME = 15 SECONDS 6-54 Magellan® 8300/8400 Scale Features Scale LED Enable This feature enables/disables Scale LED (Yellow LED) operation. Scan your selection from the two bar codes below. You'll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. Complete the programming sequence by scanning the SWITCH bar code. SCALE LED = DISABLE SCALE LED = ENABLE Product Reference Guide 6-55 Scale Diagnostics Mode Enable Enables/disables the ability for the operator to initiate scale diagnostics. Scan your selection from the two bar codes below. You'll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. Complete the programming sequence by scanning the SWITCH bar code. SCALE DIAGNOSTICS MODE = DISABLE SCALE DIAGNOSTICS MODE = ENABLE 6-56 Magellan® 8300/8400 Scale Features Scale Calibration Notification When enabled, this feature allows the host to be notified of a calibration event. Scan your selection from the two bar codes below. You'll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. Complete the programming sequence by scanning the SWITCH bar code. SCALE CALIBRATION NOTIFICATION = DISABLE SCALE CALIBRATION NOTIFICATION = ENABLE Product Reference Guide 6-57 Scale Intercharacter Delay Sets the delay between the end of one character and the beginning of the next, in 10 millisecond increments. Scan the bar code below, SET KEYBOARD WEDGE INTERCHARACTER DELAY. You'll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. Scan the appropriate digits from the keypad in Appendix C that represent the desired delay. The selectable range is 0-100, which is the delay in 10-millisecond increments. Pad all single and double digit numbers with leading zeroes to yield a three-digit entry (000-100). Examples: 001 = 10ms 005 = 50ms 040 = 400ms 100 = 1, 000ms (1 second) 4. The scanner will automatically exit Programming Mode when the appropriate amount of digits have been scanned. SCALE INTERCHARACTER DELAY 6-58 Magellan® 8300/8400 Scale Features Remote Display -- Enable/Disable The scanner-scale can be configured to operate with or without a Remote Display. Recalibration/recertification may be required when adding a Remote Display. Consult your local Weights and Measures authority. NOTE If this feature is enabled the scanner-scale will expect that it is connected to a Remote Display, and will indicate an error if one is not. See Chapter 4, Error Codes, for more information. REMOTE DISPLAY = DISABLE REMOTE DISPLAY = ENABLE Product Reference Guide 6-59 EAS Features EAS Active State Specifies the active state polarity of EAS (Electronic Article Survellance); the inactive state is its opposite polarity. EAS output goes active during the good read indication of a bar code, allowing the EAS device to deactivate a tag on the product. Scan your selection from the bar codes below. [. . . ] Example: ']e001044123456789'. DataBar Expanded · · Prefix must be ASCII characters ']e0'. Label length excluding prefix characters must be at least 1 character. Maximum length is the maximum label size supported by the scanner. Example: ']e001900123456789083103001750'. · I 2 of 5 · · Check character must be included in label data. [. . . ]