User manual DAXTEN RACKACCESS

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. © Copyright 2003. Daxten, the Daxten logo, RackAccess and The Brains Behind KVM Switching and Sharing are trademarks of Daxten Industries. [. . . ] Due to the possible deviations between these video adapters, you may make some adjustment to fit the monitor for adapter used. Adjustment Procedure First, you must activate the OSD screen through pressing the MENU key, the screen will show in the centre of screen as below 800 x 600 60. 3HZ / 37. 9KHZ AUTO ADJUSTMENT Menu Menu DOS TXT / GFX off user 100 VERSION SVGAAH1511-100 Figure 1 - The OSD Screen Note: In the last paragraph, we will assume that you had already done this procedure and only explain how to change the setting. Use the & key to select the required adjustment item up or down. Use the & key to do the desired function or go into the second menu item to do the further change. Auto-Adjustment We strongly recommend that you use the Auto-Adjustment to get the optimized visual quality. Use the & key to select auto-adjustment, then press or to get the optimized quality. RGB Adjustment Use the & key to select the icon, then press or , the screen will display as below Figure 2 ­ RGB Adjustment Adjust the Contrast Value Use the & key to select the CONTRAST item, press or to get the best contrast optimization. You can adjust R, G, B, values simultaneous or R, G, B values individually, (you can use this item to change the RGB purity. ) Colour Balance Use the & key to select the balance item, then press & to get the best colour balance effect or separate set the RGB colour value. (You can use this item to change the RGB intensity) The easy way to adjust the contrast and colour balance setting is to use the auto-balance item. Geometry Adjustment Use the & key to select the icon, then press & , then the screen will display as below Figure 3 ­ Geometry Adjustment If you want to go back to the previous OSD menu screen, pressing the MENU key, you will see the OSD screen as shown in Figure 1. Vertical & Horizontal Position adjustment Use the & key to move to the the centre position. Use the & key to move to the to the centre position. icon, then press & to move the whole screen left or right to icon, then press & to move the whole screen down or up Adjust the viewing screen size Use the & key to move to the icon, then press & to get the larger viewing size. PHASE adjustment Adjust phase tracking of display signal to reduce the display flicker. The invalid phase tracking will cause unstable and flicking display. Use the & key to move to the Phase item, then press & to get better image quality. DOS TXT/GFX Now, you can select the display mode as 640 x 400 (called graphic mode), or 720 x 400 (called Text mode). Colour Temperature We provide three modes, one is user mode, one is 6500 and the other is 9300. Use the & key to move to the colour temperature, then press & to select the colour temperature setting. When set at 6500 or 9300, you can not change the value. Brightness Adjustment Use the & key to select the icon then press & to change the brightness value. The Display Resolution Setting In the OSD screen, you will see the horizontal frequency (HF), vertical frequency (VF), display resolution (MODE) and the monitor firmware version (ROM LEVEL). It is automatically detected by the monitor, and you can not change this setting. Service Information Technical Support If you cannot determine the nature of a problem, please call Daxten and ask for Technical Support. If possible, call from a phone located near the unit, as we may be able to solve your problem directly over the phone. If we cannot solve your problem, and determine that the fault is in the unit, we will issue a Return Material Authorisation (RMA) number that must appear on the outside of all returned products. The unit should be double-packed in the original container, insured, and shipped to the address given to you by our Technical Support representative. The Technical Support offices are found on the back of this manual. Limited Warranty Daxten warrants to the end user that this product is and will be free from defects in materials and workmanship for a period of 24 months from the date of purchase. If during the warranty period the product should fail, the purchaser must promptly call Daxten for a RETURN MATERIALS AUTHORIZATION (RMA) number. [. . . ] EXCEPT AS EXPRESSLY PROVIDED ABOVE AND TO THE MAXIMUM EXTENT ALLOWED BY LAW, DAXTEN SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES (INCLUDING WITHOUT LIMITATION, LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF INFORMATION, FINANCIAL LOSS, PERSONAL INJURY, LOSS OF PRIVACY OR NEGLIGENCE) WHICH MAY BE CAUSED BY OR RELATED TO, DIRECTLY OR INDIRECTLY, THE USE OF A PRODUCT OR SERVICE, THE INABILITY TO USE A PRODUCT OR SERVICE, INADEQUACY OF A PRODUCT OR SERVICE FOR ANY PURPOSE OR USE THEREOF OR BY ANY DEFECT OR DEFICIENCY THEREIN EVEN IF DAXTEN OR AN AUTHORIZED DAXTEN DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSSES. Waste Electrical and Electronic Equipment (WEEE) Within the European this symbol indicates that this product should not be disposed in household waste. It should be deposited at an appropriate facility to enable recovery and recycling. [. . . ]