User manual DAXTEN SCOUTUSB

[. . . ] Select Push-button or keyboard Hot Key control. Comes with Auto-Scan mode for convenient automatic switching. Front panel status LEDs give a clear indication of the active PC. Flash Upgrade Flash upgradeable firmware allows you to obtain the latest firmware upgrades for your switch. This allows you to maintain compatibility with the latest devices and computers. [. . . ] Connect the USB connector to a USB port on your computer. Connect the green audio jack to the speaker port on your computer. Connect the pink audio jack to the microphone port on your computer. 2. 3. Power up the first computer, and then verify keyboard and mouse functionality. Repeat this process for each of the attached computers. If you find that the keyboard or mouse is not working correctly please verify that all cables are properly connected, and that the HID drivers are loaded on the computer. Rear Panel Layout 4-Port switch Using the SCOUTusb The SCOUTusb provides two methods to select the desired computer. You may use either the Select button on the unit, or make use of the keyboard Hot Key commands. You may notice that the mouse cannot be used for around 2 seconds when the SCOUTusb switches to another computer. This is normal and is caused by the synchronization process which ensures that the mouse operates correctly. Selection buttons 2 Port: Pressing the Select button on the front panel cycles through computers 1 ~ 2. 4 Port: Pressing the individual PC buttons will switch the signal to the desired computer. Keyboard Hot Key commands To send Hot Key commands to the SCOUTusb switch, press and release Ctrl Ctrl within 2 seconds. Press a command key for the desired effect. The following commands are supported: First Key Ctrl Ctrl Ctrl Ctrl Ctrl Ctrl Ctrl Second Key Ctrl Ctrl Ctrl Ctrl Ctrl Ctrl Ctrl Command Key C 1 , C 2 , C 3 or C 4 H 1 , H 2 , H 3 or H 4 A 1 , A 2 , A 3 or A 4 S 0 Command Result Switches to the desired PC Switches the hub to the desired PC Switches all to the desired PC Switch to previous PC Switch to next PC Toggle Sound ON / OFF Toggle Auto-Scan mode ON / OFF Note: Directly select Channel or Hub. For example, if you press: Ctrl Ctrl C 2, means the Channel on the port 2 not the Hub Ctrl Ctrl H 2, means the Hub on the port 2 not the Channel Ctrl Ctrl A 2, means all, Channel and Hub In Auto-Scan mode, the image shown on the monitor will automatically switch to the next computer. The delay is user definable (see Table above). After the last computer has been shown, the first computer will be shown again. Note: In this mode there is no mouse or keyboard control. Press any key to exit the Auto-Scan mode. The SCOUTusb switch will stop at the last PC shown. The Hot Key sequence can be changed if required. To change from the factory default of Ctrl please use the following sequence: [OLD HOT KEY] [NEW HOT KEY] for example: Ctrl Ctrl Scroll Lock Scroll Lock New Hot Key: Scroll Lock Scroll Lock The following combinations are available for Hot Keys: Ctrl Ctrl (default) Alt Alt Scroll Lock Scroll Lock Ctrl, Shift Shift Built-in 2-Port Hub Attaching any USB device to the 2-Port hub, that device will be automatically switched as you Switch PCs. Service Information Technical Support If you cannot determine the nature of a problem, please call Daxten and ask for Technical Support. If possible, call from a phone located near the unit, as we may be able to solve your problem directly over the phone. If we cannot solve your problem, and determine that the fault is in the unit, we will issue a Return Material Authorisation (RMA) number that must appear on the outside of all returned products. The unit should be double-packed in the original container, insured, and shipped to the address given to you by our Technical Support representative. [. . . ] If the product is used in contradiction to any instruction provided by any User Guide or Instruction Sheet provided to you or with the product. EXCEPT AS SPECIFICALLY PROVIDED ABOVE AND TO THE MAXIMUM EXTENT ALLOWED BY LAW, DAXTEN DISCLAIMS ALL WARRANTIES AND CONDITIONS WHETHER EXPRESS, IMPLIED, OR STATUTORY AS TO ANY MATTER WHATSOEVER INCLUDING, WITHOUT LIMITATION, TITLE, NON-INFRINGEMENT, CONDITION, MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR OR INTENDED PURPOSE. EXCEPT AS EXPRESSLY PROVIDED ABOVE AND TO THE MAXIMUM EXTENT ALLOWED BY LAW, DAXTEN SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES (INCLUDING WITHOUT LIMITATION, LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF INFORMATION, FINANCIAL LOSS, PERSONAL INJURY, LOSS OF PRIVACY OR NEGLIGENCE) WHICH MAY BE CAUSED BY OR RELATED TO, DIRECTLY OR INDIRECTLY, THE USE OF A PRODUCT OR SERVICE, THE INABILITY TO USE A PRODUCT OR SERVICE, INADEQUACY OF A PRODUCT OR SERVICE FOR ANY PURPOSE OR USE THEREOF OR BY ANY DEFECT OR DEFICIENCY THEREIN EVEN IF DAXTEN OR AN AUTHORIZED DAXTEN DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSSES. Waste Electrical and Electronic Equipment (WEEE) Within the European this symbol indicates that this product should not be disposed in household waste. It should be deposited at an appropriate facility to enable recovery and recycling. [. . . ]