User manual DAXTEN VOYAGER MICRO BROCHURE

[. . . ] Transmitter available in PS/2 and USB Operation The Voyager Micro is simple to install, no software is required. Just connect the units up as described in quick setup system guide and you're ready to work. Switch the computer off before wiring up the units. Installation Before connecting your computer to the Voyager Micro Transmitter unit, please ensure that your computer is powered off. Connect your console devices to the Voyager Micro Receiver unit. [. . . ] Connect the Voyager Micro Transmitter unit to your computer's Keyboard Monitor and Mouse ports (If using the USB transmitter then plug the USB plug into your computers USB port). Plug in your Keyboard, Monitor and Mouse into the corresponding Keyboard, Monitor and Mouse ports on the Voyager Micro's Receiver unit. Connect your UTP cable to the Voyager Micro's Transmitter and Receiver units. Connect the power supply unit to the Voyager Receiver unit. Check that the keyboard and mouse operate correctly. Adjust the picture tuner on the Voyager Micro Receiver unit if required. Note: Although we would recommend connecting the Voyager Micro to a computer that is turned off, you can connect it to a computer while it is turned on. To do so you must connect it in the following order: 1. Place cables away from fluorescent lights, air conditioners, and machines that are likely to generate electrical noise 3. 8. LED indicators The Voyager Micro Transmitter and Receiver units both have 2 LEDs above the RJ45 port. The flashing yellow LED indicates the system is connected. Upgrading the firmware The update software and the latest firmware are available from our website www. daxten. com, in the product support section. There you will also find instructions on how to perform the upgrade. Configuration options Configure the Voyager Micro to: Work with Unix servers Input the monitor's DDC information Change the hotkey from Shift to Ctrl Enter the Voyager Micro configuration mode by pressing Shift Tab ­ as set out below - all 3 LEDs illuminate. Pressing Esc exits the configuration mode and the LEDs return to normal. Note: Press the keys one after the other not all together. Working with Unix servers Configure the system to work with Unix servers UNIX Version HP UX, SGI and Open VMS Alpha Unix AIX Hotkey Shift Shift Shift Key 1 Tab Tab Tab Key 2 U U U Key 3 1 2 3 Key 5 Esc Esc Esc DDC (Display Data Channel) Information DDC is a VESA standard for communication between a monitor and a video adapter To enter the monitor's DDC information into the Transmitter's memory, press: Shift Tab D Esc Ensure that you update the information when you change the monitor. This is done by simply repeating the hotkey sequence shown above. Changing the Shift hotkey to Ctrl You can change the hotkey to Ctrl Once you do so, replace all the instances of Shift appearing above to Ctrl . To change the hotkey to Ctrl press: Shift Tab C Esc To change the hotkey back to Shift press: Ctrl Tab S Esc Quick Setup Guide Service Information Technical Support If you cannot determine the nature of a problem, please call Daxten and ask for Technical Support. If possible, call from a phone located near the unit, as we may be able to solve your problem directly over the phone. If we cannot solve your problem, and determine that the fault is in the unit, we will issue a Return Material Authorisation (RMA) number that must appear on the outside of all returned products. The unit should be double-packed in the original container, insured, and shipped to the address given to you by our Technical Support representative. The Technical Support offices are found on the back of this manual. Limited Warranty Daxten warrants to the end user that this product is and will be free from defects in materials and workmanship for a period of 24 months from the date of purchase. [. . . ] If the product is used in contradiction to any instruction provided by any User Guide or Instruction Sheet provided to you or with the product. EXCEPT AS SPECIFICALLY PROVIDED ABOVE AND TO THE MAXIMUM EXTENT ALLOWED BY LAW, DAXTEN DISCLAIMS ALL WARRANTIES AND CONDITIONS WHETHER EXPRESS, IMPLIED, OR STATUTORY AS TO ANY MATTER WHATSOEVER INCLUDING, WITHOUT LIMITATION, TITLE, NON-INFRINGEMENT, CONDITION, MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR OR INTENDED PURPOSE. EXCEPT AS EXPRESSLY PROVIDED ABOVE AND TO THE MAXIMUM EXTENT ALLOWED BY LAW, DAXTEN SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES (INCLUDING WITHOUT LIMITATION, LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF INFORMATION, FINANCIAL LOSS, PERSONAL INJURY, LOSS OF PRIVACY OR NEGLIGENCE) WHICH MAY BE CAUSED BY OR RELATED TO, DIRECTLY OR INDIRECTLY, THE USE OF A PRODUCT OR SERVICE, THE INABILITY TO USE A PRODUCT OR SERVICE, INADEQUACY OF A PRODUCT OR SERVICE FOR ANY PURPOSE OR USE THEREOF OR BY ANY DEFECT OR DEFICIENCY THEREIN EVEN IF DAXTEN OR AN AUTHORIZED DAXTEN DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSSES. Waste Electrical and Electronic Equipment (WEEE) Within the European this symbol indicates that this product should not be disposed in household waste. It should be deposited at an appropriate facility to enable recovery and recycling. [. . . ]