User manual DE DIETRICH 6455ENX

[. . . ] This heat is then transmitted to the food. In order for an induction hob to operate the cookware must have a ferrous base (containing Iron). A simple rule is if a magnet sticks to the base of your pan then it should be suitable for use on induction hobs. When you buy your cookware, make sure that one of these logos are on the package; it assures you that it is compatible with induction cooking. Cookware To verify that your cookware is suitable, place it on a heating area on power 4. - If the display remains on, your cookware is compatible. [. . . ] The power delivered by the independent electronics is split between these two zones. If "boost" is selected on one zone the power is reduced on the other to ensure the maximum connected load is not breached. From time to time you may wish to select "Boost" on more than one zone; this can be done from selecting one on the right of the appliance and one on the left. Suitable cookware If the display on the appliance flashes when set, this is an indication that either there is no pan on the zone or, an unsuitable pan is being used. Please refer to the pan guide in the description section of this guide for further details. 3 Additional functions and safety Features EN Protection against overflows. In case of overflow, or of a metallic object or wet cloth placed on the control areas, the hob turns itself off, the displays light up and a beep sounds. Clean the hob or remove the object, then begin cooking again. Temperature limiter. Each cooking zone is equipped with a safety sensor that constantly monitors the temperature of the bottom of the cookware. If you leave empty cookware on a zone which is turned on, it will automatically limit the power in order to prevent damage to the cookware or hob. Residual heat. After a long cooking period, the zone used can remain hot for several minutes. An `'H'' flashes during this period. - Keep your finger on the touchpad "H", until the indicator is illuminated, - Adjust the power during cooking in the normal way with touch pads "E" or "F" this can be adjusted up to five times in any cooking cycle, allowing a minimum of 10 seconds for each power level change to register (if the number of settings exceeds 5 "NO" will be displayed on the display) To save the setting at the end of cooking press the touchpad of the corresponding zone. To reproduce the cooking the same zone used in the initial cooking must be selected followed by "MeMo" ("NO" will be displayed if a different zone is selected). The programmed power levels will be displayed in sequence followed by the start of cooking. 5 Additional Functions and Safety Features EN Timer Functions Each zone of the appliance can be controlled by using the timer function to turn off the zone after a set period of time. Select the zone required and adjust the power as required. press the timer controls "G" and using the "+" or "-"keys select the cooking time required. The appliance will now count down the time and turn off as required. when the time remaining is less than 1 minute the display will indicate seconds remaining. at the end of the time a beep will indicate the end of cooking. Independant timer The timer function can be used as an independant timer if required. Select a zone not in use and select the Timer control "t" will flash. Using the timer keys "G" select the time required "t" will become fixed and the countdown will begin. Adjusting the factory preset levels With the hob turned off, press and hold the preset to be adjusted, while pressing the preset adjust to the required power level. Preset one can be adjusted between level 1 -5 preset two between 6-10 preset three between 11-15 No adjustment can be made to the boost function. Pre Heat / Heat up Pre-heat / Heat up This Function will preheat the contents of the pan to boiling temperature before reducing to your selected power. [. . . ] TYPES OF STAINS/SPOTS Light accumulation of baked-on stains/dirt. Shiny metal Aesthetic faults to the hob top which does not entail a lack of function, are not covered by our guarantee. Full terms of the guarantee are available at www. dedietrich. co. uk. Maintaining your appliance 7 Installation Guide EN Installation Your appliance should be positioned so that the mains switch is accessible. The distance between the edge of your appliance and the side and rear walls (or partitions) must be at least four centimetres (area A). [. . . ]