User manual DE DIETRICH DHD306WE1

[. . . ] E El símbolo en el producto o en su embalaje indica que este producto no se puede tratar como desperdicios normales del hogar. Este producto se debe entregar al punto de recolección de equipos eléctricos y electrónicos para reciclaje. Al asegurarse de que este producto se deseche correctamente, usted ayudará a evitar posibles consecuencias negativas para el ambiente y la salud pública, lo cual podría ocurrir si este producto no se manipula de forma adecuada. Para obtener información más detallada sobre el reciclaje de este producto, póngase en contacto con la administración de su ciudad, con su servicio de desechos del hogar o con la tienda donde compró el producto. [. . . ] * Provide the room with an adequate aeration when a cooker hood and appliances fed by energy other than electric power (gas-, oil-, or coal- stoves, etc. ) are used simultaneously. The cooker hood, when evacuating the sucked air, could generate a negative pressure in the room- which can't exceed the limit of 0. 04 mbar, in order to avoid the suck of exhausts deriving from the heat-source. Therefore the room should be provided with air-intakes to allow a costant flow of fresh air. If the rating lable in the cooker-hood shows the symbol , the appliance is built in class II° and it does not need any earth connection. If the rating lable in the cooker-hood does not show the symbol , the appliance is built in class I° and it needs the earth connection. * When performing the electrical connections on the appliance, please make sure that the current-tap is provided with earth connection and that voltage values correspond to those indicated on the label placed inside the appliance itself. * Before carrying out any cleaning or maintaining operations, the appliance needs to be removed from the electric grid. If the appliance is not provided with a non-separable flexible cable and plug, or with another device ensuring omnipolar disconnections from the grid, with an opening distance between the contacts of at least 3 mm, then such disconnecting devices must be supplied within the fixed installation. If the fixed appliance is endowed with a supply cord and a plug, the appliance has to be put in a place where the plug can be reached easily. * The use of materials which can burst into flames should be avoided in close proximity of the appliance. When frying, please pay particular attention to fire risk due to oil grease. The superior end of the pipe is to be fixed laterally to the pipe bearing (Fig. 11Y) by using the two self-threading screws. Now mount the inferior chimney by inserting it through the front side of the cooker hood and then turning it down until it is fixed inside (Fig. 11). Filtering version * In the filtering version the air deviator is fixed through the screws supplied (Fig. 12), by using the holes which are on the back of the upper telescopic section. Connect the flange of the appliance with the air deviator through an appropriate pipe. Connect the appliance with the electric mains. (For versions with display only) Lift the lower pipe until the cable strap coming out of the sucking unit is uncovered and connect it to the display cable strap. Put down the lower pipe while paying attention it is being properly introduced into the hood. Mod. SL TC - Touch Control version (Dis. 21) A: Light switch On/Off B: Reduce speed C: Luminous telltale D: Incrase speed E: 10 - minute timer The touch control key allows the function desired by touching the relative key. The luminous telltales (C) positioned at the center of the keyboard indicate the suction speed set. In case of an active timer, the upper telltale (C) flashes. If the push button console malfunctions, remove the grease filters and press the red button inside the appliance twice. [. . . ] In case two cooker hood-remote control systems are present in a same room or nearby, the two systems could influence one another since their transmission codes are identical. In this case to change one radio control code is recommended. Changing the transmission code: To change the transmission code, please follow these instructions: Open the battery-covering panel; select a dip at will choosing between n. To replace the dichroic lamp, remove the lamp (Fig. [. . . ]