User manual DE DIETRICH DHG690XP1

[. . . ] When making the electrical connections, check that the voltage values correspond to those indicated on the data plate inside the appliance itself. In case your appliance is not furnished with a non separating flexible cable and has no plug, or has not got any other device ensuring omnipolar disconnection from the electricity main, with a contact opening distance of at least 3 mm, such separating device ensuring disconnection from the main must be included in the fixed installation. If your unit features a power lead and plug, position this so the plug is accessible. Always switch off the electricity supply before carrying out any cleaning or servicing operations on the appliance. ATTENTION: This appliance must be grounded. [. . . ] To clean the inside of the appliance, use a cloth (or brush) dipped in denatured ethyl alcohol. DESCRIPTION OF THE APPLIANCE The description and characteristics shown in this document are for information only and not obligatory. Indeed, we reserve the right to carry out any modification or improvement of the quality of certain of our products without prior notice. As with all hoods, these apparatuses can be installed in either filtering version or duction version. 1), the air and vapours conveyed by the appliance are depurated by charcoal filter and recirculated around the room. ATTENTION: Using the hood as a filtering one it is necessary to use the charcoal filters that purifies the air sent back into the room. 2), cooking vapours and odours are conveyed straight outside by a disposal duct which passes through the wall/ceiling. Use of charcoal filters is therefore unnecessary. Decide at the beginning which type of installation to adopt. Your apparatus is supplied in the filtering version so that if you want to install the apparatus in the duction version you must remove the carbon filters. This apparatus conforms to the 16. 08. 89 regulation relating to the limitation of radio-electric disturbances (EC Directive n. /6. 889 modified by the EC Directive 8/. 308. ). Fig. 2 INSTALLATION It is advisable to entrust the installation operations to specialised personnel. 7 Technical data - DHG316XP: - 1 Motor - power 135W - Voltage: 230-240V single phase - 2 halogen lamps 20W - Supplied with 150 cm electricity supply cable with plug. - Gross weight: Kg. 8, 4 - Net weight: Kg. 6, 9 - 1 metallic grease filter Technical data - DHG376XP: - 1 Motor - power 300W - Voltage: 230-240V single phase - 2 halogen lamps 20W - Supplied with 150 cm electricity supply cable with plug. - Gross weight: Kg. 10, 4 - Net weight: Kg. 8, 9 - 1 metallic grease filter Technical data - DHG386XP: - 1 Motor - power 300W - Voltage: 230-240V single phase - 2 halogen lamps 20W - Supplied with 150 cm electricity supply cable with plug. - Gross weight: Kg. 8, 2 - Net weight: Kg. 7, 2 - 2 metallic grease filters Technical data - DHG356XP: - 1 Motor - power 155W - Voltage: 230-240V single phase - 2 halogen lamps 20W - Supplied with 150 cm electricity supply cable with plug. - Gross weight: Kg. 8, 4 - Net weight: Kg. 6, 9 - 1 metallic grease filter Technical data - DHG377XP: - 1 Motor - power 300W - Voltage: 230-240V single phase - 2 halogen lamps 20W - Supplied with 150 cm electricity supply cable with plug. - Gross weight: Kg. 10, 5 - Net weight: Kg. 9, 5 - 2 metallic grease filters Dimensions (Fig. 8 DHG316XP DHG356XP DHG376XP DHG377XP DHG386XP ELECTRICITY CONNECTION While connecting the electricity make sure that the tension is that indicated in the technical lable. Before proceeding to cleaning or maintenance operations remove the tension. Connecting the electricity must be performed by a specialised technician in conformity with the regulation in force. This apparatus is constructed so as to belong to the I insulation class and therefore needs grounding. MAINTENANCE REMOVE THE TENSION AT THE HOOD (PLUG or SWITCH) BEFORE ANY OPERATIONThorough servicing guarantees correct and long-lasting operation. -Maintenance of the casing: Avoid products containing abrasives when cleaning the casing. [. . . ] 9a, 9b) need to be removed first in order to remove the carbon filters. Remove the two metal filter retainers (M) and position the charcoal filter inside the grease filter; fit the two filter retainers back on again to secure the charcoal filter (Fig. 10). Change the carbon filters and remount the anti-grease filters. Fig. 10 -Changing the halogen lamps: To change the halogen bulbs open the cover levering from the proper slots (Fig. 11). [. . . ]