User manual DE DIETRICH DME555XD1

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual DE DIETRICH DME555XD1. We hope that this DE DIETRICH DME555XD1 user guide will be useful to you.

Lastmanuals help download the user guide DE DIETRICH DME555XD1.


Mode d'emploi DE DIETRICH DME555XD1
Download
Manual abstract: user guide DE DIETRICH DME555XD1

Detailed instructions for use are in the User's Guide.

[. . . ] Mounting plate is located on back side of microwave oven. See Figure 2. BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS: Model Number Label Mounting plate ( Remove from oven to install. ) Back of oven Figure 1 Figure 2 WARNING FOR YOUR SAFETY: · You will need TWO people to install this oven. It is heavy and could cause personal injury if not handled properly. The dimensions of the oven are as follows: Height : 16 7/16 inches Width : 29 15/16 inches Depth : 15 5/8 inches Weight : 60 lbs. · Avoid Electrical Shock! ­ Before you drill into the wall, note where electrical outlets are and where electrical wires might be concealed behind the wall. [. . . ] 73 ft. STEP 3: PREPARE THE VENTING BLOWER Your microwave oven is shipped with the blower assembled for roof venting. You need to adjust the blower if you want wall-venting or room-vented (recirculating) installation. ELECTRICAL SHOCK HAZARD!UNPLUG UNIT BEFORE WORKING ON IT. · DO NOT PULL OR STRETCH THE BLOWER WIRING!Pulling and stretching the blower wiring could result in electrical shock. WARNING REMOVE THE MOUNTING PLATE: 1. Remove any shipping materials and parts from inside the microwave oven. Cover the countertop or cooktop with a thick, protective covering to protect it from damage and dirt. See Figure 10. A thick, protective covering NOTE: If you have a free-standing range, disconnect it, move it onto a piece of cardboard or hardboard and pull it away from the wall, so that you can get closer to the upper cabinet and back wall for easier measuring and drilling. 3. Remove mounting plate screw(s) (1 or 2 screws) from the mounting plate as shown and discard (see Figure 11). This plate will be used to locate and mark the mounting holes on the rear wall. (It will be used to locate and mark the mounting holes on the rear wall. ) 5. Locate exhaust adaptor, grease filters and hardware packet. Drill a 3/8" hole at points J and K on the upper cabinet template. NOTE: If the bottom of the upper cabinet is recessed 3/4" or more, you will need 2"x2" filler blocks (not included) to provide additional support for the bolts. · Mark the center of each filler block and drill a 3/8" diameter hole at the mark. · Align filler blocks over the two openings in the top of the microwave oven cabinet and attach to cabinet with masking tape. See Figure 25. cabinet front filler block cabinet bottom shelf filler block Figure 24 Figure 25 3. Cut or drill a 2" diameter hole at the area marked M, "power supply cord hole" on the upper cabinet template. If the upper cabinet is metal, you will need to cover the edge of the hole with the power supply cord bushing (supplied) to prevent damage to the cord from the rough metal edge. WARNING YOU MUST COVER THE EDGE OF THE POWER SUPPLY CORD HOLE IN A METAL CABINET WITH THE POWER SUPPLY CORD BUSHING. FAILURE TO DO SO COULD RESULT IN DAMAGE TO THE CORD AND ELECTRIC SHOCK. 4. Cut out the venting areas (with the saber saw): · Roof-Vented: · Wall-Vented: cut out the shaded area marked L on the upper cabinet template. go to STEP 5, INSTALL THE MOUNTING PLATE, located on page 16. 5. Use caulking compound to seal the exterior wall or roof opening around the wall cap or roof cap. [. . . ] This will give the location and size of the box cutout for the rear wall duct. · Attach the exhaust adaptor to the rear mounting plate by sliding it into the guides at the top center of the plate on the wall side. Push in securely until it is past the top locking tabs and in the lower locking tabs. Take care to assure the damper hinge is installed so that it is at the top and that the damper swings freely. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE DE DIETRICH DME555XD1

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual DE DIETRICH DME555XD1 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag