User manual DE DIETRICH DRS623JE

[. . . ] We wanted to offer you a product of excellence. In the DE DIETRICH product range, you will also find a wide choice of hobs, ovens, microwaves, dishwashers, cookers, fridges, freezers, that you can coordinate with your new DE DIETRICH hood. Visit our website www. dedietrich-electromenager. com, where you will find our latest innovations as well as useful and complementary information. DE DIETRICH Setting New Values As part of our commitment to constantly improving our products, we reserve the right to make changes to them based on technical advances to their technical and functional features and appearance. Warning : Before installing and using your appliance, please carefully read this Guide to Installation and Use, which will allow you to quickly familiarise yourself with its operation. Contents UK - Instruction on mounting and use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Read this manual carefully before installing or using your apparatus because it contains important information for your safety and for whoever installs or uses it. This apparatus has been created to be installed in a kitchen and for normal domestic use. Do not use it for commercial or industrial purposes or other purposes for which it was not created. Do not modify or try to modify the characteristics of this apparatus. It would be dangerous for you. Installation The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood must be not less than 45cm from electric cookers and 65cm from gas or mixed cookers. 34 If the instructions for installation for the gas hob specify a greater distance, this must be adhered to. The mains power supply must correspond to the rating indicated on the plate situated inside the hood. If provided with a plug connect the hood to a socket in compliance with current regulations and positioned in an accessible area. If it not fitted with a plug (direct mains connection) or if the plug is not located in an accessible area apply a bi-polar switch in accordance with standards which assures the complete disconnection of the mains under conditions relating to overcurrent category III, in accordance with installation instructions. Warning: Before re-connecting the hood circuit to the mains supply and checking the efficient function, always check that the mains cable is correctly assembled. 5-6 Before beginning installation: · Check that the product purchased is of a suitable size for the chosen installation area. · To facilitate installation, remove the fat filters and the other parts allowed and described here, dismantle and mount it. · Only for chimney installation: Apply the support bracket , , G" to the adherent ceiling, use the chimney support bracket as a hole scheme (if present, the small eyelet found on the support should coincide with the line previously traced on the wall) and trace with a pencil 2 holes, drill the holes (Ø8mm), insert 2 plugs. Fasten the support bracket to the wall with 2 5x45mm screws (4). · Open the vapour scheme and remove the grease filters (see relevant paragraph). · Hang the hood (5), regulate the position (6-7) and fasten it securely with one screw and washer(8). · Carry out electrical connections (9), but leave the hood disconnected from the general electrical main panel. · Install the flange supplied on the exit hole of the hood (10a). · Carry out the connection of one tube (11 ­ tube and ties for fastening not included, they need to be bought) for the fume discharge to the connection ring placed on top of the extractor motor unit. The other end of the tube should be connected to a fume expulsion device towards the outside, in case the hood is used in extractor version. · Fix the upper cover with 3 screws. (12) Note: this is supplied already mounted in some cases. · Only for chimney installation: In case you want to use the hood in filtering version, fasten the deflector F to the support bracket, and connect the other side of the tube to the connection ring placed on the deflector (13). Apply the chimneys and fasten them on with two screws (14a) to the chimney support bracket , , G" (14b). [. . . ] Eliminate excess water without damaging the filter, then put it in the oven for 10 minutes at 100° C to dry completely. Replace the mattress every 3 years and when the cloth is damaged. · Montage Open the steam screen and remove the grease filter. Install the carbon filter on the back of the grease filter and 36 · fix with two rods. [. . . ]