User manual DE DIETRICH DTE411FL1

[. . . ] -- Using a gas cooking appliance results in the generation of heat and humidity in the location where it is installed. Please ensure that your kitchen has proper ventilation: keep natural ventilation orifices open or install a mechanical device (mechanical ventilation hood). -- Intensive, prolonged use of the appliance may require additional ventilation; you can, for example, open a window or provide more effective ventilation by increasing power to the mechanical ventilation, if you have it. -- Do not store CLEANING products or FLAMMABLE products (aerosol cans or containers under pressure, as well as papers, cookbooks, etc. ) in the cabinet underneath your cooking hob. [. . . ] You must use the holes provided for this purpose, according to the diagram above (Fig. Stop screwing when the mounting bracket starts to become deformed. Do not use a screwdriver. The safety wire (green-yellow) is connected to the appliance's ground terminal and must be connected to the ground lead of the electrical set-up. The fuse in your set-up must be 10 amperes. If the power cable is damaged, it must be replaced by a cable or a special kit available from the manufacturer or its After-Sales Service Department. Tip In order to easily locate the reference information for your appliance, we recommend that you note them on the "After-Sales Service Department and Customer Relations" page (this page also explains to you where to find this information on your appliance). 43 1 / INSTALLING YOUR APPLIANCE · GAS CONNECTION · Preliminary comments If your hob is installed above an oven or if proximity to other heating elements poses a threat of overheating the connection, you absolutely must insulate the cable in a rigid pipe. If a hose or soft pipe (in the case of butane gas) is used, it should not come into contact with a moving part of the cabinet, nor should it pass through a location that may become blocked. The gas connection must be installed in compliance with applicable regulations in the country of installation. · Gas distributed by pipe; natural gas For your safety, you must choose from the three following connection options: -- Connection with a rigid pipe made from copper and with screw-on mechanical connectors (G1/2 gas standard mark) Make the connection directly to the end of the elbow fitted on the appliance. -- Connection with a wavy metal hose (stainless steel) with screw-on mechanical connectors (compliant with NF D 36-121 standard) whose service life is unlimited (Fig. -- Connection with a reinforced rubber hose with screw-on mechanical connectors (compliant with the NF D 36-103 standard) whose service life is 10 years (Fig. B). Warning When connecting your hob's gas supply, if you have to change the direction of the elbow fitted on the appliance: Change the gasket. Screw on the elbow's nut, careful not to exceed a torque of 17 N. m. Q @ ; Q @ ; Fig. 05), using a small flat-head screwdriver, by turning two times counterclockwise. Each burner is controlled by a tap fitted with a safety system that, in the event of accidental flame extinction (spills, draughts, etc. ), quickly and automatically cuts the gas supply and prevents it from being released. Each burner is supplied by a tap that is opened when you press in the knob and turn it in a counterclockwise direction. The "o" point corresponds to a closed tap. -- Select the desired burner by referring to the symbols located near the knobs (e. g. Your hob is fitted with a burner-lighting system built into the knobs. -- To light a burner, press on the knob and turn it in a counterclockwise direction to the maximum setting . -- Continue to press on the knob to produce a series of sparks until the burner lights. The setting for more moderate flame intensities are between the symbol and the symbol. Fig. 01 Tip In order to ensure the proper lighting of the double crown burner, we suggest that you light it before placing cookware on it. When a knob becomes difficult to turn, do not force it. [. . . ] Do not allow acidic liquids such as lemon juice, vinegar, etc. To clean the hob's stainless steel, use a sponge and soapy water or a commercially available special stainless steel product. Warning It will be easier to maintain your hob if you clean it before it has completely cooled down. However, never clean your appliance while it is in operation. Set all the gas controls to zero. Tip -- It is better to clean the parts of the hob by hand rather than in the dishwasher. [. . . ]