User manual DE DIETRICH DTI1177X

[. . . ] Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information. This information has been provided in the interest of your safety. You MUST read it carefully before installing or using the appliance. Installation q Check your dishwasher for any transport damage. If your dishwasher is damaged, you should contact your supplier. [. . . ] The programme must be cancelled: press simultaneously the function push buttons 2 and 3 for about 2 seconds. All the indicator lights will turn off (except for the On/Off indicator light and eventually salt and rinse aid indicator lights) indicating that the setted programme has been cancelled and the machine is now in setting mode. Press simultaneously function push buttons 2 and 3, until the indicator lights of the function push buttons 1, 2 and 3 start flashing. Press the function push button 2, the indicator lights of function push buttons 1 and 3 turn off while the indicator light of the function push button 2 goes on flashing, at the same time the indicator light End of programme illuminates indicating that the inflow of rinse aid is active. To deactivate the inflow of rinse aid, press the function push button 2 again, the indicator light End of programme turns off, indicating that the inflow of rinse aid has been deactivated. To memorise the operation, switch off the dishwasher by pressing the On/Off push button or wait about 60 seconds after which the dishwasher will automatically return to setting mode. To activate the inflow of rinse aid follow the above instructions until the indicator light End of programme illuminates. Filling with rinse aid 1. Open the container by pressing the release button (A). Add the rinse aid until the container is completely full. The maximum level for filling is indicated by "max". Ensure that the lid is closed after every refill. Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash. Forks and spoons should be placed in the removable cutlery basket with the handles facing downwards and the knives with their handles facing upwards. If the handles protrude from the bottom of the basket, obstructing the lower spray arm, load the cutlery with the handles facing upwards. Mix spoons with other cutlery to prevent them from sticking together. For best results we recommend you to use the cutlery grid provided (if the size and dimensions of the cutlery allow it). UI76 Adjusting the height of the upper basket If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position. Maximum height of the dishes in upper basket lower basket With upper basket raised With upper basket lowered 20 cm 24 cm 31 cm 27 cm To move to the higher position proceed as follows: 1. Move the front runner stops (A) of the upper basket outwards and slide the basket out. Refit the basket in the higher position and replace the stops (A) in their original position. When the basket is in the higher position you will not be able to use the cup rack(s). The upper basket The upper basket is designed for plates (dessert plates, saucers, dinner plates of up to 24 cm in diameter), salad bowls, cups and glasses. Arrange items on and underneath the cup racks so that water can reach all surfaces. Glasses with long stems can be placed upside down in the cup racks. For taller items, the cup racks can be folded upwards. Light items (plastic bowls etc. ) must be loaded in the upper basket and arranged so they do not move. US75 RC01 After loading your machine always close the door, as an open door can be a hazard. Before closing the door, ensure that the spray arms can rotate freely. US74 11 Use of detergent Only use detergents specifically designed for use in dishwashers. [. . . ] Check the water drain hose connection. Protection against flooding is active. Close the water tap and contact the Service Force Centre. Once the checks have been carried out, close the door and press the push button of the programme that was running before the intervention of the alarm, the programme will continue from the point in which it was interrupted. If the fault code reappears contact the Service Force Centre. For other combinations of fault codes not described in the above chart will appear, please contact your Service Force Centre. . . . there are problems when operating the dishwasher Fault Possible cause The dishwasher door has not been properly closed. The programme does not start The fuse has blown in the household fuse box. [. . . ]