User manual DE DIETRICH DTI306VE1

[. . . ] A poor air supply could cause lack of oxygen. Ensure that the gas supply complies with the gas type stated on the identification label, placed near the gas supply pipe. Using a gas cooking appliance will produce heat and moisture in the room which it has been installed in. Ensure a continuous air supply, keeping the air vents in good conditions or installing a cooker hood with discharge tube. [. . . ] 11 European Guarantee Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions Step by step instructions for an operation Hints and Tips Environmental information MANUFACTURER: ELECTROLUX HOME PRODUCTS ITALY S. p. A. Viale Bologna, 298 47100 FORLÌ (Italy) Description of the appliance 1 1 Ultra-Rapid Burner - 4, 0 kW 2 Burner Control Knob 2 Instruction for the User Burner Control Knob The hob burner control knob is situated on the hob front panel. The symbols on the knob mean that : there is no gas supply there is maximum gas supply / Ignition setting there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support. Push the relevant knob down and turn it anti-clockwise until it reaches the "maximum" position. After lighting the flame, keep the knob pushed down for about 5 seconds. This will allow the "thermocouple" (Fig. 1 lett. D)to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. Then, check the flame is regular and adjust it as required. 3 If you cannot light the flame even after several attempts, check the "cap" (Fig. To put the flame out, turn the knob to the symbol . In the absence of electricity, ignition can occur without the electrical device; in this case approach the burner with a flame, push the relevant knob down and turn it anti-clockwise until it reaches the "maximum" position. Always turn the flame down or put it out before taking the pans off the burner. Carefully supervise cookings with fats or oil, since these types of foodstuff can result in a fire, if overheated. The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top. Avoid installing the appliance in the proximity of inflammable materials (e. g. The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. THE MANUFACTURER WILL NOT ACCEPT LIABILITY, SHOULD ANY OF THE OTHER SAFETY INSTRUCTIONS INCORPORATED IN THIS BOOK OR THE REGULATION IN FORCE BE IGNORED. · · 6 Gas connection Choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. Use the same attention when the hob is combinated with an oven. IMPORTANT - To ensure a correct operation, a saving of energy and the long-life of the appliance, the voltage pressure of the appliance must correspond to the recommended values. The adjustable connection is fixed to the comprehensive ramp by means of a threaded nut G 1/2". Interpose the sealing between the components as shown in Fig. Screw the parts without forcing, adjust the connection in the required direction and tighten everything. D Fig. 4 A) B) C) D) Ramp with ending nut Seal Adjustable connection Rubber pipe holder for LPG Connection using flexible non metal pipes When the connection can be easily inspected in its full extent, there is the chance to use a flexible pipe according to the rules in force. [. . . ] If changing from town gas to LPG, completely tighten clockwise the screw, until a small regular flame is obtained. Finally check the flame does not go out when quickly turning the knob from the maximum position to the minimum position. This procedure can easily be carried out, anyhow the hob has been positioned or built in the working top. 7 By-pass screw Table 1 : BY-pass diameters Burner Ø By-pass in 1/100 of mm. [. . . ]