User manual DE DIETRICH DTI805X

[. . . ] IMMEDIATELY AFTER INSTALLATION, CARRY OUT A BRIEF INSPECTION TEST OF THE APPLIANCE, FOLLOWING THE INSTRUCTIONS BELOW. SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE POWER SUPPLY AND CONTACT YOUR NEAREST TECHNICAL ASSISTANCE CENTRE. NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION (OFF) WHEN YOU FINISH USING THE HOB. 20 Introduction THE APPLIANCE DATA PLATE, WITH TECHNICAL DATA, REGISTRATION NUMBER AND BRAND NAME, IS POSITIONED AT A VISIBLE POINT UNDER THE SAFETY COVER. [. . . ] Carefully trim off the excess edge of the gasket C (Fig. 3). The dimensions in figure 2 below refer to the distance between the hole and the inside edge of the gasket. 4 until the hob has been set in place. 2) 3) 4) 22 Instructions for the installer 2. 2 Attachment to support structure, flush-mounting model Create an opening with the dimensions shown in the figure in the work surface, observing a minimum distance of 50 mm from the rear edge. The lower part of the protective cover must be fully accessible when the appliance is installed. This appliance can be installed next to walls that are higher than the work surface, as long as the distance "X" is kept, as shown in the 1) figure, to avoid damage from overheating. Make sure there is a minimum of 750 mm (Fig. 1) between the gas rings and any shelf that may be installed directly above them. This type of appliance also requires a cut 3 mm deep in the work-top with the dimensions shown in figure 4 (detail A, figure 2). Before positioning the hob, position the adhesive sponge material "E" supplied over the milled surface (fig. Now place the hob on the cut in the work-top and use the screws and fixing brackets (sequence shown in Fig. 3) to secure the hob to the supporting structure, adjusting it until perfectly horizontal. The hose connection at the rear of the appliance has a ½" internal thread (ISO 228-1). Connection with rigid copper pipe: the connection to the gas mains must not provoke stress of any kind on the appliance. Connection may be made by using biconicaladapter D with insertion of gasket C supplied. Connection with flexible steel pipe: use only flexible stainless steel pipes conforming to standard regulations in force, inserting gasket C supplied between the fitting A and the flexible pipe B. The flexible pipe must be installed so that pipe length does not exceed 1. 5 meters of maximum extension. Make sure that the pipes do not touch any moving parts or become crushed. 2. 7 Connection to LPG Use a pressure regulator and make the connection to the tank according to the provisions of standard regulations in force. Make sure that feed pressure conforms to the levels shown in the table in paragraph "3. 2 Burner and nozzle characteristics table 28 Instructions for the installer 3 ADJUSTMENT TO DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, unplug the appliance from the mains. The hob is set for natural gas G20 (2H) at a pressure of 20 mbar. In the case of functioning with other types of gas the burner nozzles must be changed and the minimum flame adjusted on the gas taps. To change the nozzles, proceed as described below. 3. 1 1. 4. Replacement of nozzles on the hob Remove the grids and all the caps and flame-spreader crowns; Unscrew the burner nozzles with a 7 mm socket wrench; Replace the nozzles according to the type of gas to be used (see paragraph "3. 2 Burner and nozzle characteristics table"). [. . . ] Note that pans larger than 28 cm diameter must be used only on the central burner. A symbol next to each knob indicates the relative burner. The device is fitted with electronic ignition. How to use: pour the product on a damp cloth and wipe the surface, rinse thoroughly and dry with a soft cloth or chamois leather. 6. 1. 2 Food stains or residues Under no circumstances must metallic scourers or sharp scrapers be used: they will damage the surface. [. . . ]