User manual DE DIETRICH DTV701X

[. . . ] This appliance is intended for domestic uses and conforms to current regulations in force. The appliance has been built to carry out the following functions: Cooking and heating-up of food. The manufacturer declines all responsibility for improper use. Do not leave the packing in the home environment. [. . . ] The plug on the end of the supply cable and the wall socket must be the same type and conform to the current electrical system regulations. Check that the power line is adequately grounded. On the power line, install an omnipolar cut-off device with contact cut-off distance greater than or equal to 3 mm, located in an easily accessible position near the unit. Do not use reducers, adapters or shunts. If the power cable is replaced, the wire section on the new cable must not be less than 1. 5 mm2 (3 x 1. 5 cable), keeping in mind that the end to be connected to the hob must have the ground wire (yellow-green) longer by at least 20 mm. Use only H05V2V2-F cable or similar which has a maximum temperature of 90°C. Any replacement needed should be carried out by a specialised technician who should make the mains connections according to the following diagram. L = brown N = blue = yellow-green The manufacturer will not be liable for any damage to persons or property caused by non-observance of the above instructions or deriving from the tampering of even a single part of the hob. GAS CONNECTION Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the provisions defined by standard regulations in force. To facilitate connection, fitting A on the rear of the appliance may be adjusted laterally. For this purpose, loosen hexagon nut B, turn fitting A to the desired position, and retighten hexagon nut B (tightness is ensured by a biconical brass ring). To replace the nozzles and regulate the burners, you have to remove the top as described in the following paragraph. Remove all the knobs, the grids, the burner caps and the flamecaps; 2. remove the screws and the nuts A that secure the burner supports; 3. replace the burner nozzles in accordance with the reference gas chart; 6. regulate the primary air as described in paragraph "5. 2 Regulation for LPG". 10 5. 2 Regulation for LPG Loosen screw A and push support B all the way. Use a double head wrench to remove nozzle C and assemble the suitable one, following the instructions indicated in the reference charts, with respect to the type of gas to use. The screwing torque of the nozzle should never exceed 3 Nm. Reposition support B so that nozzle C is covered perfectly. Move the Venturi tube D to regulate the air flow until distance "X" is reached indicated in the chart in paragraph "5. 4 Regulation of primary air" and then secure the tube by means of screw A. After the regulations have been carried out, restore the seals with sealing wax or equivalent material. Burner Rated heating capacity (2. 55 kW) Nozzle diameter 1/100 mm LPG - G30/G31 28/37 mbar By-pass 1/100 mm 30 30 37 37 65 33 (*) 33 (*) 40 (*) 40 (*) Reduced flowrate (W) 380 380 650 650 1600 Flowrate g/h G30 76 120 185 185 283 Flowrate g/h G31 75 118 182 182 279 Auxiliary (1) Semi-rapid (2) Rapid (3) Rapid (4) Ultra rapid (5) 1. 05 1. 65 2. 55 2. 55 3. 9 48 62 76 76 95 (*) By-pass value for valveless appliances. 11 Instructions for the installer 5. 3 Regulation for natural gas The hob has been inspected for LPG G30/G31 at a pressure of 28-37 mbar. [. . . ] The label is inside the bag that contains the nozzles provided. 13 Instructions for the installer 6. 3 Arrangement of burners on hob BURNERS 1. Ultra rapid 6. 4 Lubrication of gas taps After a while, the gas tap may become hard to turn or lock. If this happens, it has to be cleaned inside and re-greased. This must be done by a qualified technician. 14 Instructions for the user 7. [. . . ]