User manual DE DIETRICH DVH1140J

[. . . ] EN CONTENTS 1 / SAFETY INSTRUCTIONS • Important warnings __________________________________________ 2 / INSTALLING YOUR DISHWASHER 14 • Dimensions for building in appliances __________________________ • List of parts supplied ________________________________________ • Connecting to the water supply ________________________________ • Draining away the waste water ________________________________ • Electricla connection ________________________________________ • Insertion into the niche ______________________________________ • Levelling by adjusting the feet ________________________________ • Fitting the door panel (Cladding with a single panel) ______________ • Fitting the door panel (Cladding with two elements) ______________ • Appliances built-in under o hob ________________________________ • Fixing in the niche __________________________________________ • Sound-proofing seals ________________________________________ • Balancing the door (left and right) ______________________________ • Refitting the plinth __________________________________________ • Table for cutting away the plinth ______________________________ 15 15 16 17 18 19 19 20 21 22 22 22 22 23 23 Important: When building in appliances, please use the attached installation diagram. Important: Please read this installations manual carefully in order to comply with the instructions for installing and fitting your machine. NB: This installations manual covers various models. There may be some slight differences between your appliance and the descriptions shown. 13 EN 1/ SAFETY INSTRUCTIONS • IMPORTANT WARNINGS Important: After unpacking your appliance, make sure that it has not suffered any damage during transport. If your appliance is damaged, please contact your dealer. Danger: If your appliance operates incorrectly, disconnect it (pull out the plug) or switch off the circuit concerned and close the water supply tap. Contact our After-Sales Service. Important: All the necessary electrical and plumbing work for installing the appliance must respectively be carried out by a qualified electrician and plumber. — Once you have installed your appliance, ensure that it is not resting on the power cable or the water supply or drain hoses. [. . . ] Testing strip Hardness Setting Traditional product 0-10°F 10-25°F 25-40°F 40-55°F 55-70°F > 70°F c0 cI c2 c3 c4 c5 Factory setting : c3 Important: It is very important to set the water softener correctly. - If the setting is too low, there is the risk of chalky marks appearing. - if the setting is too high, there is the risk of causing clouding of the glasses. If you relocate, adjust the water softener setting as required. • Traditional tablets Non-multipurpose tablets should be placed in the external compartment (Fig 04) or, for optimum performance, pull out the dispenser drawer and lay the tablet inside (Fig 05). • Powders or liquids (Fig 13) Fill at least up to the minimum mark for slightly dirty crockery and to the maximum mark for dirty crockery. If the crockery is very dirty and for programmes with a pre-wash we recommend that you add 5g of detergent (a dessert spoonful) into your dishwasher’s tub in accordance with the programmes table. Important: Keep these products out of children’s reach and away from dampness. Only use products specially designed for dishwashers. Fig. 05 EN 5/ DETERGENT PRODUCTS AND ADJUSTING THE WATER SOFTENER • FOR MULTI-PURPOSE PRODUCTS • Your appliance can be specially set to use multi-purpose if the water hardness is < 25°F. To provide better coverage of the wide range of multi-purpose products available, your dishwasher’s “AUTO 4/1” option has two possible settings, accessible via the “Set” button. “Extra Dry” improves the drying results in the event of reduced performance from the “2-in-1”, “3-in-1” or “4-in-1” types of multi-purpose product. “Sparkling Clean” enables you to prioritise the sparkle of your crockery whatever the type of multi-purpose product used. Advice: • Proceed to set water softener — Access setting mode by holding down the “SET” button until you hear a double audible signal (long beep). — The water softener setting is displayed ont he screen (for example c3). — To use multi-purpose tablets, you must select setting c0 or c1, depending on the water hardness. To do this, keep on briefly pressing one or other of the keys until you reach the desired setting. • Proceed to select the “Multi-purpose — ” option and set it : deactivates the “AUTO 4/1” option. : corresponds to activation of the “AUTO 4/1” option with the “Sparkling Clean” setting. This — enables you to prioritise a brilliant finish for your crockery. — : corresponds to activation of the “AUTO 4/1” option with the “Extra Dry” setting. “Extra dry” enhances the drying results if performance is reduced. — The “AUTO 4/1” light then illuminates permanently if this option has been selected. — The setting is validated automatically after 10 seconds if the “SET” button in not pressed again. — Pressing “SET” enables you to validate the setting and move on to the next parameter. Testing strip Hardness Multi-purpose products Function Deactivated Multi-purpose products Sparkling Clean Multi-purpose products Extra Dry “Rinsing” light lit “Drying” light lit 0-10°F c0 c0 c0 c1 c1 c1 10-25°F “multi-purpose” light flashing NB: You can deactivate the “Salt” and “Rinsing” product lights if you are using multi-purpose products; this is done by using the “SET” button (page 17) • Loading the multi-purpose tablet dispenser To assist in loading the detergent, the distributor is situated on the front of the upper basket. It is compatible with all the products recommended for dishwashers. • Place the tablet in the external compartment (Fig 04 on previous page) or, for optimum results, pull out the distributor’s drawer and lay the tablet inside (Fig 05 on previous page). - Close the dispenser. 11 EN 6/ LOADING OF REGENERATING SALT • Loading of regenerating salt (Fig 06) Filling with salt is essential for providing a good wash without marks. [. . . ] This information is shown on the description plate (see Fig. 16) ORIGINAL PARTS When maintenance is being carried out, ask for only certified original spare parts to be used. Fig. 16 30 EN 15/ INDICATIONS FOR THE TESTING LABORATORIES • Details common to all models — Washing capacity - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12 standard place settings — Arrangement of the items - - - - - - - - - - - - - - - - - - - - - - - - - - - - Figs. A-B-C; see next page — Loading as per the indications on next page, without side shelves or stemmed glass support, and 5 cup/saucer supports (4 for12 saucers & 1 for 2 cups) — Setting for upper basket - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Low position — Setting for rinsing product distributor - - - - - - - - - - - - - - - - - - 3 cI — Adjusting the water softener - - - - - - - - - - - - - - - - - - - - - - - - - - For detailed information on the comparison tests regarding the level of soiling, the types of crockery and cutlery, etc. , contact the equipment manufacturer before commencing the tests. • Tests to Standard EN 50242: — Recommended programme - - - - - - - - - - - - - - - - - - - - - - - - - - — Dosage of detergent - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 30g of detergent B • Tests according to the mixed IEC 436/DIN 44990) method — Recommended programme - - - - - - - - - - - - - - - - - - - - - - - - - - — Dosage of detergent - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - “Eco” 5 + 25g of detergent B NB: When conducting tests using a multi-function tablet: - Check that the water softener is correctly set for the water hardness — Pull out the detergent distribution drawer and place the tablet in the interior compartment. [. . . ]