User manual DE DIETRICH LDD925IX

[. . . ] - While the appliance is running, watch the children and make sure they neither stay near the equipment, nor touch the surfaces that have not cooled down completely. - Before powering the equipment, check that it is properly adjusted for the type of gas at disposal (see the "installation" paragraph). - Before carrying out the maintenance or cleaning the equipment, cut power supply off and make it cool down. - Make sure that air circulates around the gas equipment. [. . . ] Use the maximum capacity to quickly make the liquids reach the boiling temperature, and the reduced capacity to heat food or maintain boiling. All of the operating positions must be chosen between the maximum and the minimum ones, never between the minimum position and the closing point. The gas supply can be interrupted by turning the 4 ELECTRIC PLATE USE The electric-plate is operated with a seven position switch and to turn the electric-plate on, rotate the switch to any of the positions shown. The red light is switched on when the electric-plate is in operation. Below as indicative basis, the settings to be used for operating the electric-plate. Warning - Use only flat pans and with sufficiently thick base, equal or not much superior than that of the plate. - Do not switch the electric plate without the pan over the plate. - Do not cook any food on the plate surface. - Turn off the plate few minutes before the cooking end. INSTRUCTIONS FOR THE USER - After use the electric plate remains very hot for a prolonged period of time, do not tuch it and do not place any object on top of the plate. - For a good preservation, the electric plate must be thoroughly cleaned with appropriate cleaning products which are readly available. KNOB SETTING 0 1 2 3 4 5 6 NB. : When operating for the first time, it is necessary to eliminate any humidity or oil which may accumulated around the electric elements of the plate by operating the electric plate on its lowest setting (1) for about 30 minutes. HEAT Off Very low Low Mild Medium Strong Very strong TYPE OF COOKING To heat small quantities of liquids. Make a hole in the top of the piece of furniture, with the dimensions indicated in fig. 3, at a distance of at least 50 mm from the appliance border to the adjacent walls. If the hob is going to be installed on the top of an oven, precautions must be taken to guarantee an installation in accordance with current accident prevention Fig. 4 standards. Pay particular attention to the position of the electric cable and gas pipe: they must not touch any hot parts of the oven. Moreover, if the hob is going to be installed on the top of a built in oven without forced cooling ventilation, proper air vents must be installed to guarantee an adequate ventilation, with the lower air entering with a cross section of at least 200cm2, and the higher air exiting with a cross section of at least 60 cm2. Fastening the top Every cook-top is equipped with a special washer. A set of hooks is also supplied for mounting the cook-top. For the installation proceed as follows: - Remove the racks and burners from the top. - Turn the appliance upside down and lay the washer S along the external border (fig. 5). Fig. 3 MODEL DTE714X / W / F / B DTE715X / W / F / B DTE772X / W / F / B DTG764X DTG775X DTE792X DTG795X L (mm) P (mm) 560 480 860 480 Fig. 5 Fig. 6 Any possible wall unit over the cook-top must be placed at a distance of at least 760 mm from the top. It is advisable to isolate the appliance from the piece of furniture below with a separator, leaving a depression space of at least 10 mm (fig. 6 - Introduce and place the cook-top in the hole made in the piece of furniture, then block it with the V screws of the fastening hooks G (fig. 6. [. . . ] If the appliance is not equipped with a plug, apply a standardized plug to the power supply cable. It is possible to effect the connection to the electric grid directly, by interposing an omnipolar switch having a contact opening distance of at least 3 mm. GAS TRANSFORMATIONS AND ADJUSTMENTS Replacing the nozzles If the equipment is adjusted for a type of gas that is different from the one available, it is necessary to replace the burner nozzles. It must therefore be delivered to a waste recycling centre specifically for electric and electronic equipment or returned to the retailer at the moment of purchase of a new equivalent appliance. [. . . ]