User manual DE DIETRICH LDD935IXX

[. . . ] Recycling of the appliances organised by your manufacturer will thus be undertaken in optimum conditions, in accordance with European directive 2002/96/CE relating to electrical and electronic equipment waste. Contact your local authority or retailer for how to have used appliances collected or collection points. 1 Working Principle A B C Induction coils Glass insulating hob top Ferrous pan base EN The induction principle The principle of induction is based on a magnetic effect. When you place your cookware on a cooking zone and you turn it on, the electronic circuits in your cooking hob produce "induced" currents in the bottom of the cookware which instantly raise its temperature. This heat is then transmitted to the food. [. . . ] Suitable cookware If the display on the appliance flashes when set, this is an indication that either there is no pan on the zone or, an unsuitable pan is being used. Please refer to the pan guide in the description section of this guide for further details. 3 Additional functions and safety Features EN Protection against overflows. In case of overflow, or of a metallic object or wet cloth placed on the control areas, the hob turns itself off, the displays light up and a beep sounds. Clean the hob or remove the object, then begin cooking again. Temperature limiter. Each cooking zone is equipped with a safety sensor that constantly monitors the temperature of the bottom of the cookware. If you leave empty cookware on a zone which is turned on, it will automatically limit the power in order to prevent damage to the cookware or hob. Residual heat. After a long cooking period, the zone used can remain hot for several minutes. An `'H'' flashes during this period. Do not put your hand on the zone. Auto-Stop system. If you forget cooking is in progress, after a predefined time, this safety function will automatically turn off your hob (from 1 to 10 hours depending on the power setting). "AS" displays and a beep sounds after about 2 minutes. press the timer controls "G" and using the "+" or "-"keys select the cooking time required. The appliance will now count down the time and turn off as required. When the time remaining is less than 1 minute the display will indicate seconds remaining. At the end of the time a beep will indicate the end of cooking. 5 Additional Functions and Safety Features EN Pre Heat / Heat up Pre-heat / Heat upThis Function will preheat the contents of the pan to boiling temperature before reducing to your selected power. To select the function turn on the required zone then press the "-"on the power selection keys, "HU" is shown on the display, Select the power level to be maintained after the initial heat up ( this must be level 7 or above ). During the pre-heat phase the display will alternate between the selected power level and "HU", once the preheating is complete the display will revert to the power level only. This feature can be used in conjunction with the timer functions. For example you can set the appliance to preheat a pan of pasta to a boil reduce the pan to a simmer then time the entire cooking phase to ensure perfect results every time. Boil Function The boil function allows the user to heat to boiling point a quantity of water prior to adding food such as Pasta or vegetables and then maintaining the boiling for a period of time set by the user. To operate the boil function touch the "boil" icon on the touch pad, the display will then show the volume of water to be boiled in litres. The volume can then be adjusted using the "+" or "-" keys (0. 5l, 1l, 1. 5l, 2l, 2. 5l, 3l, 4l, 5l or 6l) confirm by pressing the "boil" key. A short beep and "boiL" appears on the display. [. . . ] Apply warm white vinegar to the stain, let stand, then wipe with a soft cloth Apply a cleaning agent for vitro-ceramic glass(preferably containing silicon for protection)to the surface as per product instructions Accumulation of baked- Cleaning sponges on stains/ dirt Scraper for glass Sugar spills, melted plastics etc Ring marks and rard water residue Shiny metal colourings Weekly maintenence White vinegar Special vitro-creamhob cleaner product with conditioner. 7 Installation Guide EN Installation Your appliance should be positioned so that the mains switch is accessible. The smell will disapear with use. Problems after switching on You observe that Possible causes What should you do? The hob does not operate and The machine is not switched Check electrical supply, mains there are no indicator lights on or correctly connected to switches / circuit breaker / on the display. fuses The hob is not working and an The appliance has detected a Call the after sales service "F" code is displayed fault department The hob does not function and displays the lock symbol The hob is locked Please refer to child lock fea ture. 11 Help Guide Problems while in use You observe that. Possible causes What should you do The hob has stopped working The hob has detected an and "" is displayed also an aud overflow or object covering able beep is heard the controls. [. . . ]