User manual DELONGHI CF 1130

[. . . ] Have your electrical circuit checked by a qualified electrician. Before cleaning or maintenance operations, always unplug the appliance from the mains socket. Do not move the appliance by pulling the power cable. Do not install the appliance in rooms containing gas, oil or sulphur. [. . . ] How to reconnect the quick-fit couplings To reconnect the quick-fit couplings, repeat the previous operations in reserve, taking the following precautions: · Before passing the sheath through the hole in the wall, you should protect the threaded ends of the quick-fit couplings with insulating tape or similar. · Fit the two refrigerant couplings together, making sure they are perpendicular with respect to the appliance. Screw them up a couple of turns by hand to make sure they fit together correctly, then tighten using the spanners used previously. · After connecting the two refrigerant couplings, fix the two metal mounts. · Check the tightness of the refrigerant couplings by moistening the junctions with a little soapy water. No soap bubbles should form. 4) Remove the rubber insulation around the connection. 5) Use the two spanners supplied to uncouple the two hoses. 6) Screw the caps provided onto both the disconnected parts. 7) Disconnect the condensate drain hose carefully as water may leak out. INTERNAL UNIT Install the internal unit in the room to be air conditioned. It should usually be beneath a window or in any case near an outside wall. The air intake and outlet grilles of the internal unit must always be kept free. EXTERNAL UNIT 1) The external unit can be stood on a terrace or balcony. In this case, it is not necessary to use the mounts. WARNING To avoid leaks of refrigerant while disconnecting and reconnecting the quick-fit couplings, make sure the hoses are perpendicular with respect to the appliance. Important You are recommended to have the quick-fit couplings disconnected and reconnected by a qualified professional. Important Make sure the external unit water drain hose is free from kinks or obstructions. 18 Pre p a r i n g f o r u s e 2) The external unit can be hung on a wall using the mounts supplied. In this case, proceed as follows: a) Fix the mounts to the wall, making sure they are positioned as shown in the figure. In particular cases of exceptionally high humidity, the condensate must be eliminated using the condensate drain hose (after removing the rubber cap). GB Important: The external unit must be protected from rain and bad weather. b) Hook the external unit to the mounts and fix with the screws provided. 3) Alternatively, to install temporarily, the external unit can be hung as follows: a) Attach the mounts to the external unit and fix them using the screws provided. c) Attach the other end of the belts securely. The external unit can be installed on the same level as the internal unit or higher, provided the difference in height does not exceed 1. 5 m. The air intake and outlet grilles of the external unit must always be kept free. Condensate forming during air conditioning (summer mode) is eliminated through evaporation from the external unit. 19 Control panel THE CONTROL PANEL O P IL M H G Q N A B C D E F DESCRIPTION OF THE CONTROL PANEL A ON/OFF button B MODE selection button Air conditioning, dehumidifying, fan. C Fan speed selection button (HIGH/MED/LOW) D Timer button E Programmed operation increase temperature/time button F Programmed operation decrease temperature/time button G Display Displays the temperature values set and the programmed operating time H Timer in operation indicator light I/L/M Fan speed lights N Fan mode light O Air-conditioning mode light P Dehumidifying mode light Q Alarm light 20 Operation TURNING THE APPLIANCE ON Plug the appliance into the mains. Press the ON/OFF button (A) (when turned on, the air conditioner starts operating in the same mode as when it was turned off). Press the MODE button (B) until the indicator light corresponding to the required mode lights up: Light (O): air-conditioning mode Light (N): fan mode Light (P): dehumidifying mode GB AIR-CONDITIONING MODE Ideal for hot humid weather when you need to cool and dehumidify the room. To set operation of the appliance correctly, press the + (E) or - (F) buttons until the desired temperature is displayed. Then select the fan speed by pressing the FAN button (C) until the indicator light corresponding to the required fan speed lights up: HIGH: the air conditioner operates at maximum to reach the required temperature as rapidly as possible MED reduces noise levels but still maintains a good level of comfort LOW: for silent operation The most suitable temperature for the room during the summer varies from 24 to 27°C. You are recommended, however, not to set a temperature much below the outdoor temperature. 21 Operation FAN MODE Adjust fan speed by pressing the FAN button (C) as described for the air-conditioning mode. [. . . ] All functions can be selected from either the control panel or the remote control device. Replacing the batteries · Remove the cover on the rear of the remote control; · Replace the old batteries with two new LR03 "AAA" 1. 5V batteries, inserting them correctly (see the instructions inside the battery compartment); · Replace the cover. If the remote control unit is replaced or discarded, the batteries must be removed and disposed of in accordance with current legislation as they are harmful to the environment. 19 22 21 18 19 20 TURNING THE APPLIANCE ON Plug the appliance into the mains. Press the ON/OFF button (17) (when turned on, the air conditioner starts operating in the same mode as when it was turned off). [. . . ]