User manual DELONGHI M 29

[. . . ] 8 3. 2 Emptying the wet/dry tank . . . . . . . . . . . . . . . . . . . Extraction cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4. 1 Filling the extraction cleaning tank . . . . . . 11 4. 2 Extraction cleaning accessories. . . . . . . . . . [. . . ] · Avoid vacuuming up hard or sharp objects that might damage the dustbag and the appliance itself. Do not use the appliance to vacuum up nails, pins, screws or other metal objects. · Before starting the appliance, make sure that the correct filters are properly positioned. The manufacturer reserves the right to change the specifications of the appliance and/or accessories provided prior notice. The use of original spare parts and accessories is recommended to maintain the appliance in good working order and NOT invalidate the guarantee. · This appliance is intended for domestic use only, and must be used in accordance with the operating instructions contained in this booklet and only with the tools and accessories provided. · The manufacturer shall not be liable for damage resulting from the improper use of the appliance. · For all repairs, contact an authorised Technical Service Centre only. 4 GB 2-01-2003 14:37 Pagina 5 1. Preparing for use Remove the motor unit by releasing the catches. Your appliance is equipped with an external tank. Remove the solution injection system (A) by pulling it out. A Lift off the motor unit using the handle. Remove tools out of the tank and fit the most appropriate attachment for the work to be done. Turn the appliance over and fit the wheels provided, pushing them into the special holes in the base of the tank. 2. Dry vacuuming This appliance is first and foremost a powerful and versatile vacuum cleaner. Check that the paper (22) is fitted over the motorprotection housing. 5 GB 2-01-2003 14:37 Pagina 6 The large dustbag must be positioned inside the tank. Slide the cardboard collar around the suction inlet port. Connect the flexible hose to the suction inlet port, rotating the hose coupling clockwise until securely attached. Connect the solution dispenser (5) (even though not necessary for dry vacuuming) so that it does not get in the way during vacuuming. Attach one end of the extension tubes (16) to the handgrip and the other to the appropriate accessory. 2. 1 Dry vacuuming accessories Carpet/floor brush (14) Effectively vacuums up dust from both hard floors and carpets or rugs. Crevice tool (18) For picking up crumbs, dust and other fine debris. Ideal for cleaning all those difficult-to-reach places like radiators, car interiors etc. 6 GB 2-01-2003 14:37 Pagina 7 Multi-purpose nozzle (17) For cleaning sofas, upholstery, car interiors, drapes, curtains etc. Fit the required accessory to the flexible hose, plug in the power cord and switch the appliance on by pushing the ON/OFF suction switch (3) ONLY. To stop vacuuming, press the same switch again. NEVER press the wash switch (4) when using the appliance for dry or wet vacuuming. 2. 2 Paper filter maintenance When using the appliance as a dry vacuum cleaner, replace the motor protection filter (20) regularly. When vacuuming up particularly fine dust, for example cement, talcum powder, or rubble dust, the paper filter may appear to be clean, while actually clogged, which will result in a lowered performance. In such cases, it is preferable to replace the paper filter. 7 GB 2-01-2003 14:37 Pagina 8 3. Wet vacuuming This function is useful when coping with those little emergencies when you have to mop up liquids and spills from any surface quickly and efficiently, like, for example, such as unblocking a sink or drain or dealing with minor floods from washing machines, dishwashers, basement floors, etc. [. . . ] When the water in the tank runs out, the noise level will increase once again. At this point, switch off the machine and proceed to refill the tank as described in the instruction booklet. 11 GB 2-01-2003 14:37 Pagina 12 Advice for using appliances with separate switches With separate switches it is possible to depress the wash switch (4) only and use the spray trigger to spray the cleaning solution onto the surface to be treated. Wait one or two minutes to allow the solution to soak in. Press the ON/OFF switch (3) and go over the treated surface again using the suction function only without using the spray trigger (2). [. . . ]