User manual DELONGHI PAC 26ECO96

[. . . ] The PAC 26 Super sets the temperature automatically. TECHNICAL DATA WATER FUNCTION - AIR FUNCTION Power supply voltage Frequency * Cooling capacity Cooling capacity Electric power consumption Air flow capacity Timer Dimensions: width height depth Net weight (mm) (V) (Hz) (Frig/h, W, Btu/h) (Frig/h, W, Btu/h) (A) (m /h) 3 Tab. 1 see rating label see rating label see rating label see rating label see rating label see rating label 360 24 h 560 725 365 44 Max. power consumption (air-condit. mode) (W) (kg) Technical data subject to change without prior notice * According to standard ASHRAE 128P NB. When indoor temperature exceeds 32°C, the appliance should be operated with water. IDEAL OPERATING CONDITIONS (AIR-CONDITIONING FUNCTION) ROOM TEMPERATURE ROOM HUMIDITY FACTOR FREQUENCY POWER SUPPLY VOLTAGE see rating label 21 ÷ 32°C BELOW 80% see rating label Tab. 2 19 DESCRIPTION OF MAIN FEATURES Tab. 3 Air outlet grid Programmer (timer) Control panel (press to open) Water container Castors Castor stops Water collecting tray Water container compartment door Air filter Air intake grid Warranty envelope Exhaust hose compartment Power cable compartment Handle Water collecting tray drainage tube 20 DESCRIPTION OF ACCESSORIES DESCRIPTION Tab. 4 PARTS SUPPLIED Exhaust hose 1 Stopper + flange 1 Castor stop 2 De-scaling fluid 1 Window nozzle 1 Suction cup set 1 ACCESSORY CHECK Check that all parts listed in Table 4 are included. 21 INSTALLATION FOR AIR-CONDITIONING FUNCTION Our air-conditioner is portable and versatile: it can be used as a permanent installation or wise easily moved from one room to another. The appliance must be fitted at least 30 cm. from the surrounding walls. 30 cm 30 cm When installed permanently, all air discharged from the rear hose is extracted from the room in which the PAC26Super is installed. Check that the room (particularly if it is small) is not "air-tight"; a drop in pressure could cause a malfunction and thereby activate the safety switch. [. . . ] air-cooling warning light Air-cooling key TIMER ON MEMO CONTROL THERMOSTAT Ventilation key Automatic position key Button ON/OFF Timer Air-cooling signal lamp Thermostat cursor Max. speed warning light Auto ventilation warning light SETTING THE TIMER The programmer/timer, like all clocks, must be set to the exact time. (16. 00), turn the dial in a clockwise direction (following the direction of the arrow) until the number 16 is lined up with the triangular pointer (the arrows indicates 4:00 P. M. approximately ). PROGRAMMED MODE 1) Select the desired function as shown in the chart overleaf. 2) Press the TIMER key, the "TIMER ON" signal light will come ON. 3) Make sure that the timer indicates the correct time (see instructions on setting). Operating time Funzionamento 20 21 19 N. B. : Never turn the dial in an anti-clockwise direction!The timer is in effect, an electric clock and works only if the plug is connected to the power supply. Whenever the plug is disconnected or there is a power failure, the programmer stops (the clock is then "slow") and must be re-set. The unit can be used in either programmed or nonprogrammed mode. 4) Set the operating times by pushing out the notches on the dial corresponding to the period required (each notch represents 15 mins. ) The unit will now switch on and off each day at the selected times. N. B. : To override the programmed operating times, simply press the ON/OFF key (the timer signal lamp ON will go out) NON-PROGRAMMED MODE 1) Press the TIMER ON key again, the TIMER ON signal lamp will go out). 2) Select the desired function as shown in the chart on pg. For technical reasons, the temperature is not expressed in degrees but by a line increasing in thickness. We therefore recommend that when starting up the appliance, the thermostat be turned to maximum (thick green line = maximum cold). When the desired temperature has been reached, move the cursor slowly away from the maximum cold position until the appliance is switched off by operation of the thermostat. In this way the appliance has been programmed with the exact temperature degree required, which is then maintained automatically by the thermostat. This appliance is fitted with a safety device that blocks its operation if at least 3 minutes have not elapsed from when it was last switched off. 26 16 21 20 19 16 HOW TO START UP THE CONDITIONER (see control panel on the opposite page) Plug the appliance into the mains. The signal lamp will come on . w Press the ON/OFF key. The function signal lamps flash and the out. signal lamp goes w Press the key for the function required: AIR-COOL. KEY = Ventilation = Automatic climatization AIR-CONDITIONING VENTILATION AUTOMATIC w The Min. speed warning light comes on. w The Min. [. . . ] Pour 1/4 liter of de-scaling fluid and 1 l clean water into the collecting tray situated under the container, at the bottom of the unit. c) Leave the air-conditioner to operate for about half an hour. d) Drain away all the fluid left in the tray and rinse thoroughly. The drainage tube should be open and the appliance switched on during draining. [. . . ]