User manual DELONGHI PAC A 95

[. . . ] Have your electrical circuit checked by a qualified electrician. · Before cleaning or maintenance, always unplug the appliance from the mains socket. · Never unplug the appliance by pulling on the power cable. · Do not install the appliance in rooms containing gas, oil or sulphur. [. . . ] · If you have a double window, use the sucker provided to hold the two parts of the window together (fig. 3 Keep the air hose as short and free of curves as possible to avoid bottlenecks. 2 2 1 23 AIR-CONDITIONING WITH INSTALLATION 4 If required, your appliance can also be installed semi-permanently (Fig. Proceed as follows: · Drill in an outside wall or in the window pane a 134 mm dia. hole respecting the heights shown in fig. 5. 30 cm 30 cm 5 6 in the window pane · Fit the flange accessory provided in the hole following the indications in figs. · Fit the hose in the housing at the back of the appliance (fig. · Fit the end of the hose to the flange as shown in fig. When the hose is not fitted, the hole can be closed with the flange cap. Keep the air hose as short and free of curves as possible to avoid bottlenecks. 7 in the wooden kickboard of a French window When installing the air conditioner semi-permanently, you 8 should leave a door slightly open (as little as 1 cm) to guarantee correct ventilation. in the wall: you are recommended to insulate the section of wall using suitable insulation. 24 134 DESCRIPTION OF THE CONTROL PANEL 12 1 2 3 7 4 5 12 13 14 8 11 10 1 2 3 4 5 6 7 8 Air conditioning symbol Dehumidifying symbol Fan symbol SMART symbol BOOST symbol Temperature indicator Timer symbol Alarm symbol 9 10 11 12 13 14 15 16 15 16 16 6 9 SLEEP symbol AUTOFAN indicator Speed indicator MODE button (selects the modes) Button BOOST FAN button ON/Standby button Increase (+) and decrease (-) temperature button OPERATING FROM THE CONTROL PANEL The control panel enables you to manage all the main functions of the appliance, but to fully exploit its potential, you must use the remote control unit. TURNING THE APPLIANCE ON · Plug into the mains socket. Two lines appear on the display indicating that the appliance is in standby (fig. · Press the button until the appliance comes on. The last function active when it was turned off will appear. Never turn the air conditioner off by unplugging from the mains. Always press the button , then wait for a few minutes before unplugging. This allows the appliance to perform a cycle of checks to verify operation. 25 AIR CONDITIONING MODE Ideal for hot muggy weather when you need to cool and dehumidify the room. To set this mode correctly: · Press the MODE button a number of times until the air-conditioning symbol appears. · Select the target temperature by pressing the or button until the corresponding value is displayed. · Select the required fan speed by pressing the FAN button. Four speeds are available: Maximum speed: to achieve the target temperature as rapidly as possible Medium speed: reduces noise levels but still maintains a good level of comfort Low speed: for silent operation AUTOFAN: the appliance automatically selects the most suitable fan speed in relation to the temperature set on the digital display. The most suitable temperature for the room during the summer varies from 24 to 27°C. You are recommended, however, not to set a temperature much below the outdoor temperature. DEHUMIDIFYING MODE Ideal to reduce room humidity (spring and autumn, damp rooms, rainy periods, etc). In dehumidifying mode, the appliance should be prepared in the same way as for air conditioning, with the air exhaust hose attached to enable the moisture to be discharged outside. To set this mode correctly: · Press the MODE button a number of times until the dehumidifying symbol appears. [. . . ] The water should never be hotter than 40°C. After washing, leave the filter to dry then attach the intake grille to the appliance. 12 START - END OF SEASON OPERATIONS START OF SEASON CHECKS Make sure the power cable and plug are undamaged and the earth system is efficient. Follow the installation instructions precisely. END OF SEASON OPERATIONS 13 To empty the internal circuit completely of water, remove the cap (fig. [. . . ]