User manual DELONGHI T RD 0820E R

[. . . ] - It is important to ensure that the socket is adequately earthed. - This appliance complies with EEC Directive 89/336 relating to electromagnetic compatibility. How to use your heater Plug the heater into the electric socket and the light will come on. Setting the clock (fig. 2) Set the clock to the correct time, proceeding as follows: · Press the "hour" (9) button until the display (1) shows the hours for the correct time, then release the button. · Press the "min" (8) button until the display (1) shows the minutes for the correct time, then release the button. [. . . ] 4) Press the "ON MODE" (7) button (it is recommended to select the maximum power level). Set the temperature to 5°C with the " -" (6) button. "TIMER ON" yellow lamp starts to flash and this situation will persist as long as 5°C is set. When set in this way, the appliance will switch on automatically only if the room temperature falls below 5°C, thereby preventing freezing, at minimum energy consumption. Note: This function is not garanteed in the event of power failures, lasting more then 2 minutes. 4 °C Programming the Electronic Timer The timer allows you to set two programs in a 24h period. To program the timer: Press the "Timer function A" (2) ; this accesses the program and the following - The flashing message "--:--"; - The message "ON" at the bottom left (ON time setting); - The symbol "A" at the right indicating that the first program controlling is being set; To setting the starting time press "hour button" (9) to set the hour and "min button" (8) to set the minutes, then confirm the ON time by pressing the "Timer function A" (2) button again. The words "OFF" and "00:00" appear on the display. - Set the time you want the appliance to go off using the "hour button" (9) and "min button" (8), then confirm the off time by pressing the "Timer Function A" (2) button again (fig. 5). - At this point, the word "AUTO" appears at the top of the display and the "TIMER ON" (3) indicator light comes on to indicate that the appliance is ready to operate at the programmed time maintaining the preset comfort temperature. - To set the program B press "Timer function B" (4) button and follow the same procedure as described for the program A. - Use the " +" (6) or " -" (5) buttons to set the desired comfort temperature, as described above. - When set in this way the heater will automatically switch on at the set time for the designated time period and automatically maintain the preset comfort temperature. To cancel a preset programme, press the timer button A or B once and then press the hour button until the display shows "--:--" (fig. 6). is displayed: 1 10 9 8 7 2 3 4 6 5 fig. 5 AUTO Remote Control Operation fig. 6 - When you press the the frost protection push button, the radiator will set the temperature to 5°C and will switch on automatically only if the room temperature falls below 5°C, thereby preventing freezing, at minimum energy consumption. The "Timer ON" light on the control panel will flash. - Press the increase/decrease temperature button (+/-) to adjust the temperature from 5°C to 35°C. - The "Off" button switches off the appliance. Every time you press a button, the appliance will confirm the selection with a "beep" and the pilot light on the remote control will illuminate. Pilot light OFF Frost protection button Increase temperature button Decrease temperature button + - 5 Important You must leave the heater plugged in at the mains socket to keep the heater's memory programmed. [. . . ] Do not use this heater in rooms which have an area smaller than 4m2 as this may lead to overheating. Children or infirm persons should not be allowed to use this product unsupervised Children should not be allowed to play with this appliance The heater must never be placed immediately under a fixed mains socket. When scrapping the appliance, respect legislation on the disposal of oil. The use of an extension lead is not recommended, however if it is neccessary then follow carefully the extension lead's instructions, and most importantly ensure that the extension lead is correctly rated in accordance with the heater being used and NEVER overloaded. [. . . ]