User manual DELONGHI WALL-MOUNTED TOWEL WARMER SCW200

[. . . ] 3 0, 6m 0, 6m 2 EF : L P1 P2 G H : P1 P2 I : P1 P2 SCW200 SCW100 fig. 4 ÂÈÎ. 4 rys. 4 Obr. 4 abu. 4 3 IMPORTANT WARNINGS Read this manual thoroughly before using the appliance. This will ensure optimum results and maximum safety. Save these instructions for future reference. [. . . ] 6. Never use accessories or devices other than those provided by the manufacturer. 9. For all technical operations, including replacement of the power cable, contact authorised service centres only to avoid all risk. Never use water directly on the appliance or in the immediate vicinity. NEVER IMMERSE IN WATER. ELECTRICAL CONNECTION - Before plugging in, make sure the voltage of your household mains supply corresponds to the voltage indicated on the appliance. - Make sure the rating of the socket is adequate for the data given on the appliance rating plate. - THIS APPLIANCE COMPLIES WITH DIRECTIVE 89/336/EEC AND D. M. 476/92 ON ELECTROMAGNETIC COMPATIBILITY. INSTALLATION IMPORTANT: - before drilling the wall make sure there are no wires or pipes in the area; - the appliance must be installed by qualified personnel only. 1. To fix your towel warmer to the wall, use the "D" brackets, screws and anchors provided (4 for the single model SCW100 and 6 for the double model SW200) (see fig. IMPORTANT: When installing the appliance, respect the safety distances indicated in fig. 2. When positioning the appliance, make sure the control panel is out of reach of someone in the bath or shower. 1 Keep the appliance at a distance or at least 50 cm from inflammable objects and substances. The socket used by this appliance must be outside areas where the presence of water could represent a source of risk (fig. Proceed as follows: · Identify the most suitable location to install the appliance, respecting safety distances from surrounding materials and in such a way that the electrical disconnecting devices are easily accessible; · Fix the "D" brackets respecting the distances indicated in fig. 1: · Hang the towel warmer on the two brackets previously fixed to the wall. Mark the positions of the remaining fixing points on the wall ("B" only for the single version SCW100, "B" and "C" for the double version SCW200); · Remove the towel warmer, drill the wall and insert the anchors. · Re-hang the towel warmer on the brackets and fix it with the screws supplied, then fit the covers provided (fig. 2); · The appliance must not be installed immediately under a fixed socket. Bracket "ON" indicator light "Timer on " indicator light "P1" programme "P2" programme "Mode" button "Clock set" button (setting time) OPERATION AND USE 1. Setting the clock When connected to the mains for the first time or each time mains power comes back on, 0 "0 0 : 0 0" flashes on the display. It is now possible to set the clock by pressing the "Clock Set" button and proceeding as follows: · single pressure of the "Clock set" button · first 20 secs of continuous pressure · uous pressure after 20 secs the clock goes forward one minute; the clock goes forward slowly; the clock goes forward fast. Once setting has been completed, the flashing continues for several seconds, then indicates the exact time steadily. To set the clock again, just hold the "Clock set" button down for several seconds until the time display starts to flash The time can now be set following the instructions described above. 2 2. Functioning in manual mode When connecting to the mains for the first time or each time the mains supply comes back on, the appliance is in manual mode ("MAN" displayed at the top right). [. . . ] Note: If no turning off time is set, the system automatically takes 0 "0 0 : 0 0". 3 3 Pr emer e pulsante · After programming, if at least one automatic programme is active (P1 or P2) ("AUTO" displayed and "Timer on" LED lit), the " " indicator flashes when the current time is not within the programmed time band (the system is off and in stand-by waiting for the current time to coincide with the programmed start-up time) and on steadily when the current time falls within the programmed time band (towel warmer on). You can switch from automatic to manual mode at any time by pressing the "Mode" button ("MAN" displayed and appliance off). · After programming, if no automatic programme (P1 or P2) is activated, the appliance returns to manual mode and "MAN" and "0" are displayed. MAINTENANCE Before carrying out maintenance, always make sure the appliance is unplugged from the mains. This appliance requires no particular maintenance. [. . . ]