User manual DENON AVR-1400

[. . . ] Cleaning ­ Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Attachments ­ Do not use attachments not recommended by the product manufacturer as they may cause hazards. Water and Moisture ­ Do not use this product near water ­ for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. [. . . ] EFFECT LEVEL: Adjust the strength of the surround effect. DELAY TIME: (MATRIX mode only) Adjust the delay time between "0 ms" and "110 ms". To select the surround mode while adjusting the surround parameters, tone defeat or tone control, press <SURROUND MODE>, then operate the selector. 2 Perform steps 2 to 4 under "Selecting the DSP surround simulation". [DSP SIMULATION] DHFG ENTER SURROUND PARAMETER About the button names in this explanation < > : Buttons on the main unit [ ] : Buttons on the remote control unit Button name only : Buttons on the main unit and remote control unit 4 Press ENTER or SURROUND PARAMETER. 2 35 ENGLISH ENGLISH Basic Operation Basic Operation Setting the tone control Adjust the bass and treble to suit your tastes. ¢ When you do not want to adjust the tone Set "Tone Defeat" to "ON" at step 3 in "Adjusting the tone". Using the fader function With this function, the volume of all the front side speakers or all the rear side speakers can be adjusted (attenuated) at once. ¢ Adjusting the tone 1 Press SURROUND PARAMETER. 2 Press D H to select "TONE", then press F. In the direct mode, "TONE" cannot be selected. Adjusting the speaker volume 3 FG D H select 4 Pressset thetolevel. "Bass" or "Treble", then press F 3 Press [F ] to adjust the volume. G to Press G to select "OFF". Can be adjusted within the range of ­6 dB to +6 dB. 1 Press [CH SELECT]. 2 Press D H or [CH SELECT] to select the speaker. The settable speaker switches each time this button is pressed. The SW channel level can be turned off by decreasing it one step from ­12. 0 dB. OFF ´ ­12. 0 dB ´ +12. 0 dB 1 Press [CH SELECT]. 2 Press D H or [CH SELECT] to select "Fader". F the side Press [F 3 speakers, ] to attenuate the volume of allof allfront rear G [G] to attenuate the volume the side speakers. The fader function does not affect the subwoofer. It is possible to adjust so that the volume of the speaker whose volume is the lowest is ­12. 0 dB. 2 3 5 Press ENTER or SURROUND PARAMETER. 1 2 1 3 · "SB" when surround back speaker set to "1spkr". Channel blocking is available for XM radio receivers by calling 1-800-XMRADIO. Subscriptions subject to Customer Agreement available at xmradio. com. XM service only available in the 48 contiguous United States. All rights reserved. Checking the preset stations Press [ON SCREEN] repeatedly until the "Tuner Preset Stations" screen appears on the on screen display. 38 ENGLISH ENGLISH Basic Operation Basic Operation Checking the XM signal strength and Radio ID TUNING FUNCTION BAND STATUS Channel selection 1 Use <FUNCTION> to select "TUNER" or press 1 Use <FUNCTION> to select "TUNER" or press [TUNER]. 3 Press STATUS until "SIGNAL" is displayed. 2 Press BAND to select "XM". 3 Channel number · The display changes as shown below according to the receiving condition. Condition Signal strength is good Signal strength is marginal Signal strength is poor Loss of the signal XM040 DeepTrks ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡ Channel name Song title / Artist name <USER MODE> VIDEO SELECT Display GOOD MARGINAL WEAK NO 3 Press TUNING to reach the desired channel. The channel changes continuously when you press and hold TUNING. When the artist name and song title are received, they are displayed. FUNCTION [XM RADIO] Category search 4 5 Adjust the antenna location until "SIGNAL:GOOD" is displayed. Press STATUS until the XM channel (ex. XM001) is displayed. F 1 Press [F G] in the XM mode. XM006 60's CATEGORY SEARCH · The current category name is displayed. VIDEO SELECT [NIGHT] [D H F G] STATUS 6 Press TUNING to select channel 0 (XM000). XM000 RADIO ¡¡¡¡¡¡¡¡ XM006 CAT: Radio ID 60's Rock Channel category [TUNER] FUNCTION D Press F press [D 2 select [F G] to select the category, andcategory. H] to the channel within the selected TUNING BAND [D H F G] · "LOADING" is displayed while receiving the channel or information. · "UPDATING" is displayed while updating encryption code. [. . . ] · Different button is being pressed. · < and > ends of batteries inserted in reverse. · Set to a mode other than "STEREO". · Insert batteries properly. -- 3 3 3 -- 3 19 Sound is only produced from the center speaker. · The set's internal temperature has · Put the AVR-1400 in a wellventilated place. risen and the protection circuit has · Turn off the power, then wait for the been activated. [. . . ]