User manual DENON AVR-1508

[. . . ] AV SURROUND RECEIVER AVR-1508 Owner's Manual Bedienungsanleitung Manuel de l'Utilisateur Manuale delle istruzioni Manual del usuario Gebruiksaanwijzing Bruksanvisning ENGLISH DEUTSCH FRANCAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA · DECLARATION OF CONFORMITY We declare under our sole responsibility that this product, to which this declaration relates, is in conformity with the following standards: EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3. Following the provisions of 2006/95/EC and 2004/108/EC Directive. n SAFETY PRECAUTIONS RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: CAUTION · ÜBEREINSTIMMUNGSERKLÄRUNG Wir erklären unter unserer Verantwortung, daß dieses Produkt, auf das sich diese Erklärung bezieht, den folgenden Standards entspricht: EN60065, EN55013, EN55020, EN61000-3-2 und EN61000-3-3. Entspricht den Verordnungen der Direktive 2006/95/EC und 2004/108/EC. To completely disconnect this product from the mains, disconnect the plug from the wall socket outlet. The mains plug is used to completely interrupt the power supply to the unit and must be within easy access by the user. CAUTION: VORSICHT: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] The adjusted levels for the different modes are automatically stored in the memory. GAdjusting using test tonesH q Press the TEST button on the remote control unit. Test tones are output from the various speakers. w Use the o p button to adjust so that the volume is equal for all speakers. e When the adjustments are completed, press the TEST button on the remote control unit again. Getting Started [Display] 1. Sp 2. In 3. Op Q [Display] 1. Sp 2. In 3. Op Q Connections Speaker Setup Q Q Speaker Setup 17 T. Tone T. Tone Yes< 16Cr. Over 80Hz Auto > Setup Q Q [Selectable items] 40Hz 200Hz 60Hz 250Hz : 80Hz 90Hz 100Hz 110Hz 120Hz 150Hz Playback Test Tone On Q Auto-FL Only the portion of the bass sound of the various speakers output from the subwoofer that has a frequency below the frequency set here is output. Set this according to the low frequency reproduction capabilities of the speakers you are using. Test Tone Select test tone playback method. [Selectable items] Auto : Automatically switch speaker from which test tone is output. · When "System Setup" ­ "Speaker Setup" ­ "Surround Back Speaker" setting (vpage 22) is set to "1spkr" the surround back , speaker display is set to "SB" . · Speakers set to "None" in the Speaker Configuration settings are not displayed. · When "Test Tone" is adjusted, the adjusted values are set for all the surround modes. To adjust the channel level separately for the different surround modes, use the operation see page 39. Remote Control Information · The "Crossover Frequency" can be set when there are speakers that have been set to "Small" at "System Setup" ­ "Speaker Setup" or when "Subwoofer" is set to "Yes" (vpage 22). · For speakers set to "Small" sound below the crossover frequency , is cut from the sound output. The cut bass sound is output from the subwoofer or front speakers. · Always set the crossover frequency to "80 Hz" When using small . speakers, however, we recommend setting the crossover frequency to a higher frequency. Manual : Manually switch speaker from which test tone is output. Troubleshooting Test Tone Start Press the o button to select "Yes" then press the o p button to select , "Auto" or "Manual" . Auto : Press the o p button to adjust the volume. Manual : Press the u i button to select the speaker, then press the o p button to adjust the volume. When the adjustments are completed, press the ENTER button to finish the test tone. [Variable range] ­12dB ~ 0dB ~ +12dB Operations (vpage 21) ENGLISH Input Setup Use this procedure to select the input source and make the settings related to playing input sources. a, s d~h j k l A0 HDMI In Assign Digital In Assign iPod Assign Audio Delay EXT. IN Subwoofer Level Auto Preset Memory d ~ h Digital In Assign Select digital input connector to assign to this source. Getting Started Connections Setup Playback Remote Control Information Troubleshooting [Display] 1. Sp 2. In 3. Op W · With the default settings, the Control Dock for iPod can be used connected to the VCR (iPod) connector. · Even if input source is set to "iPod Assign" if the AVR-1508 is not , connected to a Control dock for iPod, the input source can be used as the normal input source. Input Setup W 3 COAX1 5 OPT1 DVD W k Audio Delay Compensate for mismatched timing between video and audio. a, s HDMI In Assign Select HDMI connector to assign to this source. CD [Display] 1. Sp 2. In 3. Op W [Input terminals] COAXIAL1 OPTICAL1 COAXIAL2 OPTICAL2 [Display] 1. Sp 2. In 3. Op W Input Setup W [Assignable input sources] CD AUX W Input Setup 1 HDMI1 DVD W CDR DVD/HDP COAXIAL1 DVD/HDP TV/CBL VCR V. AUX OPTICAL2 VCR 8 A. Delay 0ms Delay audio. This sets the delay time for audio signals. Input terminals Default setting COAXIAL2 TV/CBL OPTICAL1 CD [Variable range] 0 ms ~ 200 ms 2 HDMI2 TV NOTE This cannot be set for input sources assigned at "iPod Assign" . [Input terminals] HDMI1 HDMI2 [Assignable input sources] DVD/HDP TV/CBL VCR V. AUX HDMI1 DVD/HDP HDMI2 TV/CBL With a movie source, for example, adjust so that the movement of the actors' lips is synchronized with the sound. j iPod Assign Assign Control Dock for iPod to this source. This cannot be adjusted when playing in the EXT. IN, DIRECT or STEREO mode (with "Front Speaker" set to "Large" "Tone Defeat" to , "ON" and "Room EQ" to "OFF" . ) Input terminals Default setting [Display] 1. Sp 2. In 3. Op W · With HDMI, the video and audio signals are transferred simultaneously. At this time, set the input mode to "Auto" . [. . . ] · The subwoofer's volume is turned off. · Surround mode not set to "STANDARD (Dolby/DTS Surround)" . · Set to something other than "None" . · Select a surround playback mode. · Turn on the subwoofer's power. [. . . ]